MR VACUTAP Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 96

background image

6 Fault elimination

Maschinenfabrik Reinhausen GmbH 2020

42

5788897/03 EN

VACUTAP

®

VVS

®

6.2 Tripping the pressure monitoring device and putting the

transformer back into operation

WARNING

Danger of death or severe injury!

Danger of severe injury or death if on-load tap-changer and transformer are
insufficiently tested.

► Be sure to contact Maschinenfabrik Reinhausen to check on-load tap-

changer and transformer after the pressure monitoring device has been
tripped.

► Only use the equipment again when you are sure there is no damage to

the on-load tap-changer or transformer.

If the circuit breaker is tripped by the pressure monitoring device, proceed as
follows:

1. Establish time of tripping.

2. Determine operating position of on-load tap-changer.

3. As a precaution, block the motor-drive unit by tripping the motor protective

switch to prevent the on-load tap-changer from being actuated by remote
control.

4. Check the on-load tap-changer head cover. If insulating fluid is leaking,

close the oil conservator stop valve immediately.

5. Check whether the pressure monitoring device sensor is in the OFF posi-

tion or OPERATION position.

6.2.1 Sensor in the OPERATION position

If the sensor is in the OPERATION position, there may be an error in the trip-
ping circuit. Check the tripping circuit in this case. If you are not able to clar-
ify why the pressure monitoring device tripped, be sure to contact Maschi-
nenfabrik Reinhausen to check the on-load tap-changer.

6.2.2 Sensor in the OFF position

Proceed as follows if the sensor is in the OFF position.

1. Ensure that the transformer is not started up under any circumstances.

«
...
40
41
42
43
44
...
»

Содержание VACUTAP

































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP

Бренд: FENDT Страницы: 31

Бренд: FJC Страницы: 2

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Hammer Strength Страницы: 18

Бренд: S&C Страницы: 27

Бренд: S&C Страницы: 56

IntelliRupter PulseCloser

Бренд: S&C Страницы: 16

Бренд: S&C Страницы: 76

Бренд: Waves Страницы: 8

Бренд: Ultratune Страницы: 12

Бренд: EzCAP Страницы: 15

Бренд: ABB Страницы: 154

Quadro A Legs 3P 120 Degree Workstation with...

Бренд: Jason.L Страницы: 10

ResQCRP ResQPUMP ACD-CPR

Бренд: Advanced Circulatory Страницы: 2

Big Wheel RN1 Series

Бренд: Osborne Страницы: 8

A/C Air Launcher 101050

Бренд: CITC Страницы: 10

Magnetic Rail System Premium

Бренд: Geovent Страницы: 12

DL-FLEXILED100W/B

Бренд: Techni-Lux Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды