MR VACUTAP VR Скачать руководство пользователя страница 182

Страница: 182 / 268

8 Fitting protective devices and drive components

Maschinenfabrik Reinhausen GmbH 2015

182

4349315/00 EN

VACUTAP® VR®

Fitting vertical drive shaft

Couple drive shaft with motor-drive unit and on-load tap-changer as descri-
bed in MR operating instructions for TAPMOTION® ED.

WARNING

The motor-drive unit may be started by accident if the motor
protective switch is not tripped!

Risk of injury from starting the motor-drive unit by accident!
► Trip motor protective switch before starting to fit the drive shafts!

To fit the vertical drive shaft to the drive, proceed as follows:
1.

Grease the coupling bolts, coupling brackets and ball heads, e.g. ISO-
FLEX TOPAS L 32.

Figure 240: Grease the coupling bolts, coupling brackets and ball heads.

8.6.1

Содержание VACUTAP VR













































































































































































































































































Результаты поиска

Содержание VACUTAP VR

Отзывы:

Похожие инструкции для VACUTAP VR

Бренды по названию

Популярные бренды

MR VACUTAP VR, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание VACUTAP VR

Отзывы:

Похожие инструкции для VACUTAP VR

Бренды по названию

Популярные бренды