MR VACUTAP VR-Ex Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 256

background image

3 Product description

Maschinenfabrik Reinhausen GmbH 2020

23

7545652/00 EN

VACUTAP

®

VR-Ex

3 Product description

3.1 Scope of delivery

The product is packaged with protection against moisture and is usually de-
livered as follows:

▪ Oil compartment with on-load tap-changer head and built-in diverter

switch insert

▪ Selector

▪ Ex motor-drive unit

▪ Ex drive shaft with coupling parts and bevel gear

▪ Ex protective relay

▪ Technical files

Please refer to the delivery slip for full details of scope of delivery.

On-load tap-changers can also be provided as an on-load tap-changer set
with a common motor-drive unit.

Note the following information:

▪ Check the shipment for completeness on the basis of the shipping docu-

ments.

▪ Store the parts in a dry place until installation

▪ The product must remain in its airtight, protective wrapping and may only

be removed immediately before installation

You will find more information in the "Packaging, transport, and stor-
age" [

Section 4, Page 35] chapter.

3.2 On-load tap-changer

3.2.1 Function description

On-load tap-changers are used to adjust the transmission ratio of transform-
ers without interrupting the load flow. This makes it possible to compensate
for aspects such as fluctuations in voltage occurring in the power transmis-
sion grid. For this purpose, on-load tap-changers are fitted in transformers
and connected to the active part of the transformer.

A motor-drive unit which receives a control impulse (e.g. from a voltage reg-
ulator) changes the operating position of the on-load tap-changer, as a result
of which the transformer's transmission ratio is adapted to the prevailing op-
erating requirements.

«
...
21
22
23
24
25
...
»

Содержание VACUTAP VR-Ex

































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VR-Ex

Бренд: GALLERY Страницы: 18

Бренд: Eagle Eye Power Solutions Страницы: 2

Бренд: Baileigh Industrial Страницы: 40

Бренд: GAPOSA Страницы: 32

Бренд: FEAM Страницы: 16

Бренд: GBC Страницы: 86

Бренд: Eaton Страницы: 12

Бренд: displayit Страницы: 6

Бренд: Wachs Страницы: 44

Бренд: CONVEY-ALL Страницы: 50

Бренд: SCHUNK Страницы: 60

Бренд: Zimmer Страницы: 54

Бренд: Marini Страницы: 67

Бренд: Giacomini Страницы: 20

Бренд: Centa Страницы: 52

ADVANTIUM PSA9240

Бренд: GE Страницы: 80

Бренд: Murdock Страницы: 2

Бренд: Advantech-DLoG Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды