manualshive.com logo in svg

MR VACUTAP VM I 1002, Руководство по эксплуатации, Страница: 7 / 82

Поделиться
Скачать
MR VACUTAP VM I 1002 Скачать руководство пользователя страница 7

1 Introduction

Maschinenfabrik Reinhausen GmbH 2020

7

4360571/02 EN

VACUTAP

®

 VM

®

1.4 Notation conventions

1.4.1 Hazard communication system

Warnings in this technical file are displayed as follows.

1.4.1.1 Warning relating to section

Warnings relating to sections refer to entire chapters or sections, sub-sec-
tions or several paragraphs within this technical file. Warnings relating to
sections use the following format:

 WARNING

Type of danger!

Source of the danger and outcome.

► Action

► Action

1.4.1.2 Embedded warning information

Embedded warnings refer to a particular part within a section. These warn-
ings apply to smaller units of information than the warnings relating to sec-
tions. Embedded warnings use the following format:

 DANGER!

 Instruction for avoiding a dangerous situation.

1.4.1.3 Signal words and pictograms

The following signal words are used:

Signal word

Definition

DANGER

Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury.

NOTICE

Indicates measures to be taken to prevent damage to property.

Table 1: Signal words in warning notices

Содержание VACUTAP VM I 1002



















































































Отзывы:

Нет отзывов