MR TRAFOGUARD ISM Скачать руководство пользователя | Manualshive

Страница: 112 / 224

background image

6 Functions and settings

Maschinenfabrik Reinhausen GmbH 2016

112

5163667/00 EN

TRAFOGUARD® ISM®

To configure the tap synchronization parallel operation method, you also
have to set the following parameters:
▪

Master/follower current blocking

▪

Maximum tap difference

Master/follower current blocking

You can use this parameter to activate the circulating reactive current block-
ing limit for the tap synchronization parallel operation method. The device
thereby calculates and monitors the circulating reactive current in the same
manner as for the circulating reactive current minimization parallel operation
method. The Circulating reactive current blocking [

110] parameter is used

to set the limit value.

To activate circulating reactive current blocking for the tap synchronization
parallel operation method, proceed as follows:
1.

Go to

Settings > Parameters >

Parallel operation > Master/follower

current blocking

.

2.

Select the option you want.

3.

Press the

Accept

button to save the modified parameter.

Maximum tap difference

You can use this parameter to set the maximum permissible tap difference
between followers and master on the follower.

If the tap difference is greater than the set maximum tap difference to the
master, the follower immediately blocks. The follower therefore no longer at-
tempts to reach the master's tap position. After the set delay time for parallel
operation error messages has elapsed, the follower issues the

Permitted tap

difference to master exceeded

message.

To set the maximum permissible tap difference, proceed as follows:
1.

Go to

Settings > Parameters >

Parallel operation > Maximum tap

difference

.

2.

Enter the maximum tap difference.

3.

Press the

Accept

button to save the modified parameter.

Assigning a CAN bus address

You can use this parameter to assign a CAN bus address to the device. So
that all devices can communicate using the CAN bus, each device requires a
unique identifier. If the value is set to 0, then no communication takes place.
1.

Go to

Settings > Parameters > Parallel operation > CAN bus ad-

dress

.

2.

Enter CAN bus address.

3.

Press the

Accept

button to save the modified parameter.

6.6.3

«
...
110
111
112
113
114
...
»

Содержание TRAFOGUARD ISM

































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TRAFOGUARD ISM

Бренд: Sagola Страницы: 8

Бренд: Hansen Страницы: 72

Бренд: S&C Страницы: 32

Бренд: Vega Страницы: 8

Бренд: Harris Страницы: 58

Бренд: Zimmer Страницы: 17

Бренд: Vaisala Страницы: 92

Бренд: Tronair Страницы: 13

Бренд: gc Страницы: 20

Plate Processor 150

Бренд: Glunz & Jensen Страницы: 40

Flexiguard 8530595

Бренд: DBI SALA Страницы: 16

Бренд: turck Страницы: 36

Бренд: erowa Страницы: 23

Dodge Quantis BU383

Бренд: ABB Страницы: 8

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 2

GE PowerMark Plus DEH40229

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды