MR TAPCON 250 Скачать руководство пользователя страница 82

Страница: 82 / 216

8 Commissioning

Maschinenfabrik Reinhausen GmbH 2022

8595028/00 EN

TAPCON

250

3. Compare the tap position displays

of master

and follower

. All de-

vices must display the same tap position. If this is not the case, switch all
devices to the same tap position.

Figure 55: Comparing the tap position

1 Master

3 Tap position display

2 Follower

4. Press

on the follower to select manual mode.

5. If necessary, set the follower tapping direction.

6. Press

on the master to select manual mode.

7. Press

on the master to manually change the tap position.

8. Press

on the follower to select auto mode.

The follower switches to the same tap position as the master.

9. Press

on the master to select auto mode.

10. Press

on the follower to select manual mode.

11. Press

on the follower to manually change the tap posi-

tion.

After expiration of the set delay time for parallel operation errors
[

►

Page 153], there is a tap difference from the follower to the

master.

12. Press

several times on the follower to manually increase the tap

position by the number of permitted steps ("Maximum permitted tap dif-
ference") and then one further step.

After expiration of the set delay time for parallel operation errors, there
is a tap difference to follower on the master.

After expiration of the set delay time for parallel operation errors, there
is a tap difference to master on the follower.

13. Press

on the follower to select auto mode.

There is no response. All devices remain blocked.

Содержание TAPCON 250

























































































































































































































Результаты поиска

Содержание TAPCON 250

Отзывы:

MR TAPCON 250, Руководство по эксплуатации, Страница: 82 / 216

Результаты поиска

Содержание TAPCON 250

Отзывы: