MR TAPCON 250 Скачать руководство пользователя страница 81

Страница: 81 / 216

8 Commissioning

Maschinenfabrik Reinhausen GmbH 2022

8595028/00 EN

TAPCON

250

If one TAPCON® or all of the TAPCON® units indicate

Circulating reactive

current blocking limit exceeded

even though the control inputs are correctly

connected for all TAPCON® units, all of the TAPCON® units block.

This could be due to various causes. Further information is given in the
chapter Troubleshooting [

►

Section 11, Page 173].

The function test for the circulating reactive current blocking limit is com-
plete.

8.3.3.3 Checking tap synchronization method

NOTICE

Damage resulting from formation of a circulating reactive cur-
rent

If the parameters are not set correctly, damage may result from the forma-
tion of circulating reactive current and the resulting overload of transmission
lines and transformers.

► Check the transformer nameplate.

► Set device parameters in accordance with the transformer configuration.

In parallel operation in accordance with the

Automatic tap synchroniza-

tion

method, the tap positions of the transformers running in parallel are

compared. It is therefore necessary that the transformers have the same
position designation and that the

Raise

and

Lower

signals produce the

same voltage change in all transformers.

Before starting the function test, you must carry out the following steps:

1. Assign the master function to one device.

2. Assign the follower function to the other devices.

Содержание TAPCON 250

























































































































































































































Результаты поиска

Содержание TAPCON 250

Отзывы:

MR TAPCON 250, Руководство по эксплуатации, Страница: 81 / 216

Результаты поиска

Содержание TAPCON 250

Отзывы: