MR TAPCON 250 страница 58 Скачать руководство пользователя

Страница: 58 / 216

6 Mounting

Maschinenfabrik Reinhausen GmbH 2022

8595028/00 EN

TAPCON

250

6.4.2.1 Wiring requirement of installation site

Note the following when selecting the installation site:

▪ The system's overvoltage protection must be effective.

▪ The system's ground connection must comply with all technical regula-

tions.

▪ Separate system parts must be joined by a potential equalization.

▪ The device and its wiring must be at least 10 m away from circuit-break-

ers, load disconnectors and busbars.

6.4.2.2 Wiring requirement of operating site

Note the following when wiring the operating site:

▪ Route the connecting leads in grounded metal cable ducts.

▪ Do not route lines which cause interference (e.g. power lines) and lines

susceptible to interference (e.g. signal lines) in the same cable duct.

▪ Maintain a distance of more than 100 mm between lines which cause in-

terference and those which are susceptible to interference.

Figure 42: Recommended wiring

1 Cable duct for lines causing inter-

ference

3 Cable duct for lines susceptible to

interference

2 Line causing interference (e.g.

power line)

4 Line susceptible to interference

(e.g. signal line)

▪ Short-circuit and ground reserve lines.

▪ Never connect the device with a multi-wire collective pipe.

▪ For signal transmission, use shielded lines with individual conductors (out-

going conductor / return conductor) twisted in pairs.

▪ Connect full surface of shielding (360º) to device or to a nearby grounding

bar.

Содержание TAPCON 250

























































































































































































































Результаты поиска

Содержание TAPCON 250

Отзывы:

Похожие инструкции для TAPCON 250

Бренды по названию

Популярные бренды

MR TAPCON 250, Руководство по эксплуатации

Результаты поиска

Содержание TAPCON 250

Отзывы:

Похожие инструкции для TAPCON 250

Бренды по названию

Популярные бренды