MR TAPCON 250 страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 216

background image

5 Packaging, transport and storage

Maschinenfabrik Reinhausen GmbH 2022

47

8595028/00 EN

TAPCON

®

250

Visible damage

If external transport damage is detected on receipt of the shipment, proceed
as follows:

▪ Immediately record the transport damage found in the shipping docu-

ments and have this countersigned by the carrier.

▪ In the event of severe damage, total loss or high damage costs, immedi-

ately notify the sales department at Maschinenfabrik Reinhausen and the
relevant insurance company.

▪ After identifying damage, do not modify the condition of the shipment fur-

ther and retain the packaging material until an inspection decision has
been made by the transport company or the insurance company.

▪ Record the details of the damage immediately onsite together with the

carrier involved. This is essential for any claim for damages!

▪ If possible, photograph damage to packaging and packaged goods. This

also applies to signs of corrosion on the packaged goods due to moisture
inside the packaging (rain, snow, condensation).

▪ Be absolutely sure to also check the sealed packaging.

Hidden damage

When damages are not determined until unpacking after receipt of the ship-
ment (hidden damage), proceed as follows:

▪ Make the party responsible for the damage liable as soon as possible by

telephone and in writing, and prepare a damage report.

▪ Observe the time periods applicable to such actions in the respective

country. Inquire about these in good time.

With hidden damage, it is very hard to make the transportation company (or
other responsible party) liable. Any insurance claims for such damages can
only be successful if relevant provisions are expressly included in the insur-
ance terms and conditions.

5.4 Storage of shipments

When selecting and setting up the storage location, ensure the following:

▪ Protect stored goods against moisture (flooding, water from melting snow

and ice), dirt, pests such as rats, mice, termites and so on, and against
unauthorized access.

▪ Store the crates on timber beams and planks as a protection against ris-

ing damp and for better ventilation.

▪ Ensure sufficient carrying capacity of the ground.

▪ Keep entrance paths free.

▪ Check stored goods at regular intervals. Also take appropriate action after

storms, heavy rain or snow and so on.

«
...
45
46
47
48
49
...
»

Содержание TAPCON 250

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TAPCON 250

Бренд: IBM Страницы: 105

Бренд: Mamas & Papas Страницы: 16

Бренд: Baby Trend Страницы: 10

Бренд: Bartlett Страницы: 5

Бренд: Calpeda Страницы: 4

Бренд: Saga Страницы: 9

Бренд: Saftronics Страницы: 13

Бренд: Vaillant Страницы: 32

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 40

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: Valcom Страницы: 6

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: MULTISPAN Страницы: 2

Бренд: Velleman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды