MR TAPCON 250 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 216

MR TAPCON 250 Скачать руководство пользователя страница 147

9 Operation

Maschinenfabrik Reinhausen GmbH 2022

147

8595028/00 EN

TAPCON

®

250

Note that the following prerequisites must be met for the "circulating reactive
current minimization" parallel operation method:

▪ You have to use current transformers with the same rated values for all

transformers in parallel operation.

▪ If you wish to operate in parallel operation with existing devices, you have

to activate the Retrofit TAPCON® 2xx parameter.

For the circulating reactive current minimization parallel operation method
with CAN communication, you have to set the following parameters:

▪ Activate parallel operation

▪ Parallel operation method: Circulating reactive current

▪ CAN bus address

▪ Circulating reactive current sensitivity

▪ Circul. reactive current blocking limit

▪ Error if no communication present

▪ Behavior if no communication present

▪ Parallel operation error delay time

9.3.3.1.2 Circulating reactive current minimization without CAN bus

communication

With this method, you can operate several voltage regulators without a com-
munication connection (CAN bus) in parallel with circulating reactive current
minimization.

Desired cosφ

Desired cosφ

U, I, (cosφ)

T1: U, I, (cosφ)

T2: U, I, (cosφ)

M

AVR

M

AVR

T1

T2

Figure 77: Circulating reactive current minimization without CAN bus communication

The circulating reactive current is calculated using the desired power factor
parameter, the desired load stress type parameter, and the measured trans-
former current. An extra control deviation proportional to circulating reactive
current is added to the independently regulating voltage regulators as a cor-

«
...
145
146
147
148
149
...
»

Содержание TAPCON 250

























































































































































































































Отзывы:

Нет отзывов