MR TAPCON 230 AVT Скачать руководство пользователя страница 141

Страница: 141 / 166

11 Fault elimination

Maschinenfabrik Reinhausen GmbH 2021

141

7817454/02 EN

TAPCON

230 Expert

11 Fault elimination

This chapter describes how to rectify simple operating faults.

11.1 General faults

Characteristics/details

Cause

Remedy

No function

▪

Power supply

LED does not

light up

No power supply

Check the power supply.

Fuse tripped

Contact Maschinenfabrik Reinhausen GmbH.

No function

▪

AVR STATUS

LED does not

light up

Configuration error

Contact Maschinenfabrik Reinhausen GmbH.

Relay chatter

High EMC load

Use shielded cables or external filters.

Poor grounding

Check the functional ground.

Table 48: General faults

11.2 No regulation in AUTO mode

Characteristics/detail

Cause

Remedy

Device control commands have
no effect.

Local/Remote switch in motor-
drive unit switched to LOCAL.

Check operating mode. Correct if necessary.

No connection.

Check wiring as per connection diagram.

Automatic voltage regulation is
blocked.

▪

ALARM

LED lights up in accor-

dance with event configuration
and a corresponding event is
active.

Limit value with auto blocking or
auto-manual blocking behavior
has been exceeded

Check parameters. Correct if necessary.

The switching direction monitor-
ing has recorded a malfunction
and triggered the associated
event.

Check cause of event and then acknowledge
event.

The motor protective switch has
triggered. Motor protective switch
event active.

Check what caused the motor protective switch
to trigger and engage motor protective switch if
necessary.

Automatic voltage regulation is
blocked.

Signal at "Block automatic voltage
regulation" input

Check signal source.

Target-tap-position operation ac-
tive

Check configuration of target-tap-position oper-
ation function. If necessary, remedy cause.

"Blocking" function is linked to a
digital input or control system
message.

Check signal source or control system. If neces-
sary, reset.

Automatic voltage regulation is
blocked.

▪ Measured voltage too low (<

30 V)

Voltage measurement incorrect

Check voltage measurement.

Bandwidth set too high

Determine the recommended bandwidth.

Содержание TAPCON 230 AVT







































































































































































Результаты поиска

Содержание TAPCON 230 AVT

Отзывы:

Бренды по названию

Популярные бренды

MR TAPCON 230 AVT, Руководство по эксплуатации

Результаты поиска

Содержание TAPCON 230 AVT

Отзывы:

Бренды по названию

Популярные бренды