manualshive.com logo in svg

MR TAPCON 230 AVT, Руководство по эксплуатации

Поделиться
Скачать
MR TAPCON 230 AVT Скачать руководство пользователя страница 136

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

136

7817454/02 EN

TAPCON

®

 230 Expert

9.5 Motor-drive unit and control cabinet

9.5.1 Control of the motor-drive unit

9.5.1.1 Setting the switching pulse for controlling the motor-drive unit

You can use the parameters Switching pulse type, Switching pulse time and
Switching pulse pause to adapt the device switching pulse to the require-
ments of the motor-drive unit controller.

1. Go to 

Settings > Parameters > Motor and control cabinet > Motor

control

.

2. Select the desired parameter.

3. Set the parameter.

4. Press the 

Accept

 button to save the modified parameter.

Switching pulse type

You can use this parameter to toggle the switching pulse between a continu-
ous pulse or a time-controlled switching pulse.

Continuous pulse

Selecting the "Continuous pulse" option causes the device to issue the
switching pulse in AVR Auto operating mode until the measured value is
back within the bandwidth. In AVR Manual operating mode, the device is-
sues the switching pulse for as long as you press the 

 or 

 key.

If the device is operated as a follower in parallel operation in this case, then
the voltage regulator will issue the switching pulse until one of the following
requirements has been met:

▪ The set motor runtime has been reached

▪ The 

Motor running

 signal switches from state 1 to 0

▪ The tap position required by the master has been reached

A pause is enforced after every switching pulse before another switching
pulse is issued.

Time-controlled switching

pulse

Selecting the "Time-controlled switching pulse" option causes the device to
issue the switching pulse for a set duration. A pause 

 is enforced after ev-

ery switching pulse 

 before another switching pulse is issued.

If you use a motor-drive unit from Maschinenfabrik Reinhausen GmbH, you
need to select the "Time-controlled switching pulse" option.

Содержание TAPCON 230 AVT







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды