MR ECOTAP VPD 3 30D-24 Скачать руководство пользователя страница 33

Страница: 33 / 132

5 Mounting

Maschinenfabrik Reinhausen GmbH 2021

8209941/00 EN

ECOTAP

VPD

III 30D-24 / MD&C

5.3 Mounting motor-drive unit

Checking the operating position

The on-load tap-changer has to be in a defined operating position when
mounting the motor-drive unit.

DANGER!

Check the operating position prior to commissioning the

transformer, or ensure that the transformer is de-energized and secured
against reconnection. Failure to do so can lead to death or serious in-
juries.

2. Remove the transport locking plate and store it safely for later use. Do not

leave the sealing module open for long periods in order to prevent soiling
and damage to the mechanics.

Figure 9: Removing the transport locking plate

3. Check the on-load tap-changer operating position. The current operating

position is displayed by the control wheel.

Figure 10: Checking operating position (example illustration)

Содержание ECOTAP VPD 3 30D-24





































































































































Результаты поиска

Содержание ECOTAP VPD 3 30D-24

Отзывы:

MR ECOTAP VPD 3 30D-24, Руководство по эксплуатации, Страница: 33 / 132

Результаты поиска

Содержание ECOTAP VPD 3 30D-24

Отзывы: