T303.01
TVPRH
RADIO CONTROL TVPRH
ATTENTION !
The appliance must be installed only by qualified technical personnel in
compliance with the standards in force. All connections must be rated for
a 230V single-phase power supply. To disconnect the appliance from the
mains use an all-pole switch with a minimum distance of 3.5 mm between the
contacts. All wiring used must guarantee sufficient insulation as required by
electrical safety standards in force.
The programmer only carries out remote and manual movement commands.
All the necessary safety devices required by the installation are to be
organised separately. The programmer is in conformity with the RAEE and
RoHS directives and it is intended for indoor use only (IPX0). The appliance
is not intended for use by people (including children) with reduced physical,
sensorial or mental facilities, or with a lack of experience or knowledge,
unless they are supervised by a person responsible for their safety or
instruction concerning the use of the appliance. Children must be supervised
to ensure that they do not play with the appliance.
The radio frequency reception of the appliance may be disturbed by several
factors as follows:
-radio electric interferences from other appliances in the same room that are
transmitting on the same frequency
-if the appliance is housed in a metal casing; only plastic casing should be used.
1- GENERAL DESCRIPTION
Electronics for the remote control of tubular motors for rolling shutters with
mechanical or electronic travel limits incorporated in the motor.
Possibility to control the device manually or via radio (in the 868 version). The
work time is fixed at 60 seconds.
Programming is either carried out on the receiver or remotely via transmitters.
This appliance may be commanded by the standard transmitters of the series
TVLink. The standard transmitters may be memorized or cancelled in the
receiver using the command buttons.
The maximum number of codes that can be memorized is 42 .
1.1 Operating mode
It is possible to select different functioning modes. The operating mode involves
both the commands by means of push-buttons and the commands via radio. These
phases are possible only for the first 10 seconds after having given power to the
device.
1.1.1 Automatic opening and closing movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, press at the same time the push-buttons P2+P4 for 8
times and hold them pressed for two seconds. The Led will light up every time
the push-buttons will be pressed.
1.1.2 Automatic opening movement and “present man” closing movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, press at the same time the push-buttons P2+P4 for 9
times and hold them pressed for two seconds. The Led will light up every time
the push-buttons will be pressed.
1.1.3 “Present man” opening and closing movement
1) Give power to the device, the Led1 will light up for two seconds.
2) After the two seconds, pressh at the same time the push-buttons P2+P4 for 10
times and hold them pressed for two seconds. The Led will light up every time
the push-buttons will be pressed.
2- Transmitters
Use transmitters with at least 2 channels.
The transmitters are pre-coded by the manufacturer and each transmitter has its
own unique code.
Attention: if you press and hold down a transmitter button for more than 30
seconds, the transmitter with switch off automatically.
The receiver is compatible with all transmitters of the TVlink system: TVTXV,
TVTXP, TVTXC, TVTXK, TVTXQ, TVTXL.
1
TVLink RS868
3- Memorizing transmitters (we suggest that you cancel the entire memory
content before a new installation)
When the buttons P2+P4 are used at the same time (programming functions) the
led lights up each time.
The channels are memorized in pairs, ch1 with ch2, ch3 with ch4, ch5 with ch6
and ch7.
3.1- Memorizing directly on the receiver
1) Press buttons P2+P4 simultaneously for 3 times and then hold them down,
the led will light up and remain lit.
2) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To insert another pair of channels on the receiver repeat points 1 and 2.
3.2- To cancel a code on the receiver:
1) Press buttons P2+P4 simultaneous for 4 times and then hold them down, the
receiver led will flash intermittently slowly.
2) Transmit one of the two channels of the pair to be cancelled, once cancelled,
the led will light up and remain lit.
To cancel more transmitters repeats points 1-2
3.3- To cancel all codes from memory:
Simultaneously press buttons P2+P4 for 5 times and hold them down for at
least ten seconds, the receiver led will flash rapidly. Once the memory has been
cancelled the led will light up and remain lit.
4 - Memorizing via a transmitter (first installation, empty memory)
1) Press button P3 on the transmitter, the receiver led will light up and remain
lit.
2) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To insert another pair of channels via radio follow the procedure in paragraph
4.1
4.1 - Memorizing via a transmitter (ulterior transmitters) (memory
addressing procedure)
1) Press button P3 on the already memorized transmitter, the receiver led will
light up and remain lit.
2) Within 5 seconds press a channel that is already memorized in the receiver,
the led will switch off for 1 second and then light up again for 5 seconds.
3) Transmit one of the two channels of the pair to be memorized. Once
memorized the led will flash intermittently, release the button.
To memorize more transmitters repeats points 1-2-3.
4.2- To cancel a code via radio
1) Press button P3 on the transmitter for three times within five seconds, the
receiver led will flash slowly.
2) Transmit one of the two channels of the pair to be cancelled, once cancelled,
the led will switch off.
5- If memory is full
If the memory is full the led will flash three times when you are attempting to
memorize.
5.1- Errors during memorizing or cancelling
If the code is not memorized it could be due to one of the following:
- the code already exists in memory;
- the memory is full;
- the addressing procedure has not been followed correctly.
