MQ Power DCA6SPX4F Скачать руководство пользователя страница 37

Страница: 37 / 42

DCA6SPX4F GENERATOR • OPERATION MANUAL — REV. #2 (03/12/21) — PAGE 37

TROUBLESHOOTING (ENGINE/GENERATOR)

Table 11. Engine/Generator Troubleshooting

SYMPTOM

POSSIBLE PROBLEM

SOLUTION

Engine fails to start and

starter does not rotate.

Dead battery?

Replace battery.

Defective starter switch?

Replace starter switch.

Defective starter?

Replace starter.

Fuse F5 burned out?

Replace fuse.

Engine fails to start and

starter rotates.

Broken pre-heat circuit?

Check pre-heat circuit.

No fuel?

Add fuel.

Defective wiring?

Check wiring.

Engine starts, Idle Control

Switch is in OFF position and

engine remains at low speed.

Defective idle control switch?

Replace switch.

Clogged fuel strainer?

Clean or replace.

Clogged air cleaner?

Clean or replace.

Defective idle control device?

Replace.

Disconnected wiring?

Check and repair wiring.

Engine starts and Idle Control

Switch is in OFF position.

Engine speed rises and

battery discharges too soon.

Defective engine regulator?

Replace regulator.

Defective wiring?

Repair or replace wiring.

Engine starts and Idle Control

Switch is in OFF position.

Engine speed rises and

engine seems overloaded.

Defective alternator?

Repair or replace alternator.

Damaged alternator bearing?

Replace alternator bearings.

Engine starts and Idle

Control Switch is in OFF

position. Engine speed rises

and engine makes abnormal

noise.

Loose engine parts?

Check all engine parts for tightness.

Defective alternator?

Check alternator for damaged bearing or

loose clamping bolts.

Engine starts and Idle Control

Switch is in OFF position.

Engine speed rises and

remains at high speed when

Idle Control Switch is placed

in the ON position.

Defective idle control device?

Repair or replace idle control device.

Defective idle control switch?

Replace idle control switch.

Defective solenoid?

Replace solenoid.

Defective relay?

Replace relay.

Содержание DCA6SPX4F











































Результаты поиска

Содержание DCA6SPX4F

Отзывы:

Бренды по названию

Популярные бренды

MQ Power DCA6SPX4F, Руководство по эксплуатации

Результаты поиска

Содержание DCA6SPX4F

Отзывы:

Бренды по названию

Популярные бренды