Moxa Technologies NPort-IA-5250 Скачать руководство пользователя страница 59

Страница: 59 / 119

NPort IA5150/5250 Series User’s Manual

Web Console Configuration

5-31

S Registers

No.

AT command

Description

Remarks

Ring to auto-answer (default=0)

Ring counter (always=0)

No action applied

Escape code character (default=43 ASCII “+”)

Return character (default=13 ASCII)

Line feed character (default=10 ASCII)

Backspace character (default= 8 ASCII)

Wait time for dial tone (always=2, unit=sec)

No action applied

Wait time for carrier (default=3, unit=sec)

Pause time for dial delay (always=2, unit=sec)

No action applied

Carrier detect response time
(always=6, unit 1/10 sec)

No action applied

S10

Delay for hang up after carrier
(always=14, unit 1/10 sec)

No action applied

S11

DTMF duration and spacing
(always=100 ms)

No action applied

S12

Escape code guard time
(default=50, unit 1/50 sec)
to control the idle time for “+++”

Local TCP port

Setting

Factory Default

Necessity

1 to 65535

4001

Required

The TCP port that other devices must use to contact this device. To avoid conflicts with standard TCP
ports, the default is set to 4001.

Reverse Telnet Mode

Содержание NPort-IA-5250























































































































Результаты поиска

Содержание NPort-IA-5250

Отзывы:

Похожие инструкции для NPort-IA-5250

Бренды по названию

Популярные бренды

Moxa Technologies NPort-IA-5250, Руководство пользователя

Результаты поиска

Содержание NPort-IA-5250

Отзывы:

Похожие инструкции для NPort-IA-5250

Бренды по названию

Популярные бренды