Moxa Technologies ioLogik E2210 Скачать руководство пользователя

Страница: 111 / 144

ioLogik E2200 Series

Using the Web Console

5-9

AO Channels

On the

AO Channels

page, you can configure each AO (analog output) channel by clicking on the channel. The

available options are 0–10 V, and 4–20 mA. You may use the

Power On

field to specify the channel’s initial

value when the ioLogik E2240 is powered on, and the

Safe Status

field to specify the channel’s value when the

ioLogik E2240 enters Safe Status. Note that Safe Status is controlled by the Host Connection Watchdog, which

is disabled by default. If the Host Connection Watchdog is disabled, the ioLogik E2240 will never enter Safe

Status and your Safe Status settings will have no effect.

Relay Output Channel

On the

DO Channels

page, you can view the status of each DO (digital output) channel. Both fixed DO

channels and DIO channels that are acting as DO channels will be displayed.

Click on a channel to see that channel’s configuration options. DO Channels can operate in DO mode or Pulse

Output mode. In DO mode, output is either on or off. In Pulse Output mode, a configurable square wave is

generated.

Содержание ioLogik E2210
















































































































































Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды

Moxa Technologies ioLogik E2210, Руководство пользователя

Результаты поиска

Содержание ioLogik E2210

Отзывы:

Похожие инструкции для ioLogik E2210

Бренды по названию

Популярные бренды