Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя

Страница: 78 / 97

EDS-518A Series User’s Manual

Featured Functions

3-63

Bootup

This field shows how many times the EDS-518A has been rebooted or cold started.

Date

The date is updated based on how the current date is set in the “Basic Setting” page.

Time

The time is updated based on how the current time is set in the “Basic Setting” page.

System
Startup
Time

The system startup time related to this event.

Events

Events that have occurred.

NOTE

The following events will be record into EDS-518A’s Event Log table:
1.

Cold start

Warm start

Configuration change activated

Power 1/2 transition (Off

On), Power 1/2 transition (On

Off)

Authentication fail

Topology changed

Master setting is mismatched

DI 1/2 transition (Off

On), DI 1/2 transition (On

Off)

Port traffic overload

10.

dot1x Auth Fail

11.

Port link off / on

Using HTTPS/SSL

To secure your HTTP access, EDS-518A supports HTTPS/SSL to encrypt all HTTP traffic.
Perform the following steps to access EDS-518A’s web browser interface via HTTPS/SSL.

Open Internet Explorer and type

https://EDS-518A’s IP address

in the address field. Press

Enter to establish the connection.

Warning messages will pop out to warn the user that the security certificate was issued by a
company they have not chosen to trust.

Содержание EtherDevice EDS-518A Series


































































































Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды

Moxa Technologies EtherDevice EDS-518A Series, Руководство пользователя

Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды