Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя | Manualshive

Страница: 61 / 97

background image

EDS-518A Series User’s Manual

Featured Functions

3-46

Using Bandwidth Management

In general, one host should not be allowed to occupy unlimited bandwidth, particularly when the
device malfunctions. For example, so-called “broadcast storms” could be caused by an incorrectly
configured topology, or a malfunctioning device. The EDS-518A series not only prevents
broadcast storms, but can also be configured to a different ingress rate for all packets, giving
administrators full control of their limited bandwidth to prevent undesirable effects caused by
unpredictable faults.

Configuring Bandwidth Management

Broadcast Storm Protection

Setting

Description

Factory Default

Enable or disable the Broadcast Storm Protection for
multicast packet globally.

Enable/Disable

Enable or disable the Broadcast Storm Protection for
unknown multicast and unknown unicast packets
globally.

Enable
(for unknown
multicast and
unknown unicast
packet)

Traffic Rate Limiting Settings

«
...
59
60
61
62
63
...
»

Содержание EtherDevice EDS-518A Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для EtherDevice EDS-518A Series

Бренд: Cabletron Systems Страницы: 21

Бренд: Campbell Страницы: 42

Бренд: LAWO Страницы: 154

Бренд: H3C Страницы: 33

S5500-SI Series

Бренд: H3C Страницы: 1217

Бренд: 3Com Страницы: 2443

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 4

Бренд: Icidu Страницы: 10

Бренд: N-Tron Страницы: 62

Бренд: TC Electronic Страницы: 55

Бренд: Aztech Страницы: 2

Бренд: BWI Страницы: 5

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: iGateWeb.com Страницы: 6

Бренд: Axis Страницы: 98

Бренд: Digisol Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды