Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя | Manualshive

Страница: 27 / 97

background image

EDS-518A Series User’s Manual

Featured Functions

3-12

If all ports on both switch units are configured as 100BaseTX and they are operating in full duplex,
the potential bandwidth of the connection will be up to 1.6 Gbps on the EDS-518A. This means
that users can connect one EDS to another EDS by Port Trunking to double, triple, or quadruple
the bandwidth of the connection.

When configuring Port Trunking, note that:

Each EDS-518A can set a maximum of 3 Port Trunking groups (Trk1/Trk2, 2 trunk groups for
10/100M ports and Trk3 for Gigabit ports)

When you activate Port Trunking settings, some advanced functions that you setup with the
original ports will either be set to factory default values, or disabled:

y

Communication Redundancy will be set to the factory default

y

Traffic Prioritization will be set to the factory default

y

Port-based VLAN or 802.1Q VLAN will be set to the factory default

y

Multicast Filtering will be set to the factory default

y

Rate Limiting will be set to the factory default

y

Port Access Control will be set to the factory default

y

Email and Relay Warning will be set to the factory default

y

Set Device IP will be set to the factory default

y

Mirror Port will be set to the factory default

You can setup these features again on your Trunking Port.

Configuring Port Trunking

The

Port Trunking Settings

page is used to assign ports to a Trunk Group.

Step 1:

Select Trk1, Trk2, or Trk3 from the

Trunk Group

drop-down box.

Step 2:

Select Static, or LACP from the

Trunk Type

drop-down box.

Step 3:

Under

Member Ports

and

Available Ports

, select the specific ports.

Step 4:

Use

the

Up

/

Down

buttons to add/remove designated ports to/from a trunk group.

«
...
25
26
27
28
29
...
»

Содержание EtherDevice EDS-518A Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для EtherDevice EDS-518A Series

Бренд: dbx Страницы: 8

Бренд: NEC Страницы: 72

Бренд: TDC Страницы: 27

ELECTRA ELITE IPK II

Бренд: NEC Страницы: 617

VERSA DOCK - SERVICE

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 47

UP Squared 6000 Edge Computing Kit

Бренд: Aaeon Страницы: 59

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: ?omtime Страницы: 62

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Бренд: FOR-A Страницы: 72

TWR-SB0410-36EVB

Бренд: NXP Semiconductors Страницы: 26

Avenue Express Control Panel

Бренд: Ensemble Designs Страницы: 19

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренд: Juniper Страницы: 2

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды