Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя

Страница: 20 / 97

EDS-518A Series User’s Manual

Featured Functions

3-5

Port

Port

settings are included to give the user control over Port Access, Port Transmission Speed,

Flow Control, and Port Type (MDI or MDIX). An explanation of each configuration item follows:

Enable

Setting

Description

Factory Default

checked

Allows data transmission through the port.

unchecked

Immediately shuts off port access.

enabled

ATTENTION

If a connected device or sub-network is wreaking havoc on the rest of the network, the

Disable

option under

Advanced Settings/Port

gives the administrator a quick way to shut off access

through this port immediately.

Description

Setting

Description

Factory Default

Media type

Displays the media type for each module’s port

N/A

Name

Setting

Description

Factory Default

Max. 63 Characters Specify an alias for each port, and assist the

administrator in remembering important
information about the port.
E.g., PLC 1

None

Содержание EtherDevice EDS-518A Series


































































































Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды

Moxa Technologies EtherDevice EDS-518A Series, Руководство пользователя

Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды