Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя | Manualshive

Страница: 78 / 94

background image

5

Other Console Considerations

This chapter explains how to access the AWK-3131A-M12-RCC for the first time. In addition to HTTP access,
there are four ways to access AWK-3131A-M12-RCC: serial console, Telnet console, SSH console, and HTTPS
console. The serial console connection method, which requires using a short serial cable to connect the
AWK-3131A-M12-RCC to a PC’s COM port, can be used if you do not know the AWK-3131A-M12-RCC’s IP
address. The other consoles can be used to access the AWK-3131A-M12-RCC over an Ethernet LAN, or over the
Internet.

The following topics are covered in this chapter:



RS-232 Console Configuration (115200, None, 8, 1, VT100)



Configuring Through Telnet and SSH Consoles



Configuring HTTPS/SSL Secure Access Through a Web Browser



Disabling Telnet and Browser Access

«
...
76
77
78
79
80
...
»

Содержание Airworks AWK-3131A-M12-RCC































































































Отзывы:

Нет отзывов

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Express5800/E120d-M

Бренд: NEC Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

Бренд: dbx Страницы: 2

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

Бренд: Paradyne Страницы: 45

Бренд: National Instruments Страницы: 9

Бренд: Conceptronic Страницы: 2

Бренд: Matrix Switch Corporation Страницы: 61

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Procont LMC-008-IO

Бренд: janitza Страницы: 28

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: C&T Solution Страницы: 129

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды