Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя | Manualshive

Страница: 56 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-41

1st / 2nd Trap server IP/name

Setting

Description

Factory Default

IP address or host
name

Enter the IP address or name of the trap server used by your
network.

None

1st / 2nd Trap community

Setting

Description

Factory Default

Max. of 31 characters Use a community string match with a maximum of 31

characters for authentication.

alert

Status

Wireless Status

The status for 802.11 info parameters, such as Operation mode and Channel, are shown on the Wireless
Status page. The status will refresh every 5 seconds if the Auto refresh box is checked.

Certain values for 802.11 info may not show up due to different operation modes. As a result, Current BSSID
and Signal strength are not available in AP mode.

It is helpful to use the continuously updated information on this page, such as Signal strength, to monitor the
signal strength of the AWK-3131A-M12-RCC in Client, Slave, or ACC mode.

The transmission power indicated is the current transmission power being updated periodically.

«
...
54
55
56
57
58
...
»

Содержание Airworks AWK-3131A-M12-RCC































































































Отзывы:

Нет отзывов

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренд: Accuphase Страницы: 2

Бренд: ADTRAN Страницы: 2

AMB-VDX3H1 Series

Бренд: Acrosser Technology Страницы: 4

Бренд: DCE Страницы: 5

Бренд: Delta Страницы: 2

Бренд: Allied Telesis Страницы: 1

Бренд: Juniper Страницы: 825

Бренд: OpenVox Страницы: 13

Бренд: East Coast Datacom Страницы: 19

Бренд: Renesas Страницы: 4

Бренд: Moxa Technologies Страницы: 36

LMP-1202G-SFP Series

Бренд: ANTAIRA Страницы: 19

Бренд: Alarm Страницы: 5

FiberTwist G6426

Бренд: Genexis Страницы: 9

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: NBase Страницы: 18

Бренд: Gearlinx Страницы: 23

Бренд: Hawking Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды