Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя | Manualshive

Страница: 54 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-39

From e-mail address

Setting

Description

Factory Default

Max. 63 characters

Enter the administrator’s e-mail address which will be shown in
the “From” field of a warning e-mail.

None

To E-mail address 1/ 2/ 3/ 4

Setting

Description

Factory Default

Max. 63 characters

Enter the receivers’ e-mail addresses.

None

Relay

The AWK-3131A-M12-RCC has one relay output, which consists of 2 terminal block contacts on the
AWK-3131A-M12-RCC’s top panel. These relay contacts are used to indicate user-configured events and
system failure.

The two wires attached to the relay contacts form an open circuit when a user-configured event is triggered. If
a user-configured event does not occur, the relay circuit will remain closed. For safety reasons, the relay circuit
is kept open when the AWK-3131A-M12-RCC is not powered.

Relay Event Types

You can check the box for Active to enable the event items. All default values are deactivated (unchecked).
Details for each event item can be found in the “System log Event Types” table on page 3-31.

«
...
52
53
54
55
56
...
»

Содержание Airworks AWK-3131A-M12-RCC































































































Отзывы:

Нет отзывов

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренд: Lauterbach Страницы: 61

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

Бренд: Cabletron Systems Страницы: 21

Бренд: Palm Страницы: 4

Бренд: National Instruments Страницы: 17

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: Rane Страницы: 4

3C13886 - Router OC-3 ATM SML Flexible Interface...

Бренд: 3Com Страницы: 171

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Бренд: Queclink Страницы: 9

Бренд: Niveo Страницы: 155

ION 1200 Series

Бренд: PaloAlto Networks Страницы: 90

Бренд: u-blox Страницы: 29

kontron KBox E-420-R1K/V1K

Бренд: S&T Страницы: 82

Бренд: Advantech Страницы: 36

Бренд: ICP DAS USA Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды