Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя | Manualshive

Страница: 48 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-33

SNMP Agent

The AWK-3131A-M12-RCC supports SNMP V1/V2c/V3. SNMP V1 and SNMP V2c use a community string match
for authentication, which means that SNMP servers access all objects with read-only or read/write permissions
using the community string public/private (default value). SNMP V3, which requires you to select an
authentication level of MD5 or SHA, is the most secure protocol. You can also enable data encryption to
enhance data security.

The AWK-3131A-M12-RCC’s MIB can be found in the software CD and supports reading the attributes via SNMP.
(Only get method is supported.)

SNMP security modes and security levels supported by the AWK-3131A-M12-RCC are shown in the following
table. Select the security mode and level that will be used to communicate between the SNMP agent and
manager.

Protocol
Version

Setting on
UI web page

Authentication
Type

Data
Encryption

Method

SNMP
V1, V2c

V1, V2c
Read
Community

Community string No

Use a community string match for
authentication

V1, V2c
Write/Read
Community

Community string No

Use a community string match for
authentication

SNMP V3 No-Auth

No

No

Use account with admin or user to access
objects

MD5 or SHA

Authentication
based on MD5 or
SHA

No

Provides authentication based on HMAC-MD5,
or HMAC-SHA algorithms. 8-character
passwords are the minimum requirement for
authentication.

MD5 or SHA

Authentication
based on MD5 or
SHA

Data
encryption
key

Provides authentication based on HMAC-MD5
or HMAC-SHA algorithms, and data encryption
key. 8-character passwords and a data
encryption key are the minimum requirements
for authentication and encryption.

The following parameters can be configured on the SNMP Agent page. A more detailed explanation of each
parameter is given below the following figure.

«
...
46
47
48
49
50
...
»

Содержание Airworks AWK-3131A-M12-RCC































































































Отзывы:

Нет отзывов

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренд: D-Link Страницы: 38

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

DIR-615 - Wireless N Router

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 124

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

2Voice + 4SW VoIP Router DVG-1402S

Бренд: D-Link Страницы: 57

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

SharePort DIR-825

Бренд: D-Link Страницы: 2

Amplifi DIR-645

Бренд: D-Link Страницы: 28

Бренд: Rain Bird Страницы: 17

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды