background image

1. Drain the fuel tank completely. Stored fuel

containing ethanol or MTBE can start to go stale
in 30 days. Stale fuel has a high gum content
and can clog the carburetor and restrict fuel
flow.

2. Start the engine and allow it to run until it stops.

This ensures no fuel is left in the carburetor.
This helps prevent gum deposits from forming
inside the carburetor and possible engine
damage.

3. While the engine is still warm, drain the oil from

the engine. Refill with fresh oil of the grade
recommended in the 

Engine Manual

.

4. Allow the engine to cool. Remove the spark

plug and put 30 ml (1 oz.) of high quality motor
oil into the cylinder. Pull the starter rope slowly
to distribute the oil. Replace the spark plug.

STORAGE

If the tiller will not be used for a period longer than
30 days, following the steps below to prepare your
tiller for storage.

5. Use clean cloths to clean off the outside of the

tiller and to keep the air vents free of
obstructions.

6. Inspect for any loose or damaged parts. Repair

or replace damaged parts and tighten loose
screws, nuts or bolts.

7. Remove the tines. Clean and apply oil to the

tines and tine shafts to prevent rusting. Mount
the tines onto the tine shafts.

8. Oil the control cables and all visible moving

parts. Do not remove the engine cover.

9. To store with the handles folded down, loosen

the knobs that secure the upper handle to the
lower handles. Carefully fold the upper handle
down. Do not allow control cables to become
pinched or bent. Tighten the knobs.

Refer to the 

Engine Manual

 included in your tiller

for the information on engine maintenance. Your

Engine Manual

 provides detailed information and

a maintenance schedule for performing the
maintenance.

Engine maintenance

Air Went Screw

Grease Fitting Screw

Do not overfill. Too much grease can
create pressure which could damage
seals.

Remove the spark plug and drain all
of the oil from the cylinder before
attempting to start the unit after
storage.

Do not use strong detergents or
petroleum based cleaners when
cleaning plastic parts. Chemicals can
damage plastics.

Do not sore tiller with fuel in a non-
ventilated area where fuel fumes may
reach flame, sparks, or any ignition
sources.
Use only approved fuel containers.

14

Mowerland Tiller

Содержание MLTILL5


















Отзывы: