manualshive.com logo in svg

Move DECK001-H-UD, Инструкция по эксплуатации, Страница: 3 / 47

Поделиться
Скачать
Move DECK001-H-UD Скачать руководство пользователя страница 3

1. Manual user guide
2. Introduction to the Structural Monitoring System
3. Use and safety guidelines
4. Guide to load tests
5. DECK device
 

5.1 

Quick guide to use 

 

5.2 

DECK unpacking instructions

 

5.3 

DECK orientation

 

5.4 

DECK installation guide

6. Triaxial Tiltmeters
 

6.1 

Quick guide to use

 

6.2 

In-depth analysis of the Tiltmeter output

 

6.3 

Tiltmeter unpacking instructions

 

6.4 

Tiltmeter orientation

 

6.5 

Tiltmeter installation guide

8. Triaxial Accelerometer SHM
 

8.1 

Quick guide to use 

 

8.2 

Accelerometer SHM unpacking

 

8.3 

Accelerometer SHM orientation

 

8.4 

Accelerometer SHM installation guide 

9. Analog Communication Node
 

9.1 

Quick guide to use 

 

9.2 

Analog node unpacking

 

9.3 

Analog node orientation

 

9.4 

Analog node installation guide

10. Gateway SHM
 

10.1 

Quick guide to use 

 

10.2 

Gateway SHM unpacking

 

10.3 

Gateway SHM configuration

 

10.4 

Gateway SHM installation guide 

4
6
8

12
16
17
19
20
23

28
29
30

 33

34
35

40
41
43
44
45

48
49
51
52
55

62
63
65
66
69

11. Dimensions and overall dimensions
12. Warranty
13. Frequent problems in use
14. Note

94

100
101
102

Index

Содержание DECK001-H-UD
















































Отзывы:

Нет отзывов