Page 6
ADVANCED INFORMATION
Open the back panel of the Camera and remove the battery compartment
cover. Install four (4) C size alkaline batteries with polarities as indicated in
the Battery Compartment. Re-install the Battery Compartment Cover.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as
shown.
Turn Camera on by sliding ON/OFF switch to the ON position.
Rotate the FUNCTION SWITCH to DATE and set the date by pressing the
ENTER button and UP/DOWN buttons to adjust selected field. Rotate the
FUNCTION SWITCH to TIME and set the date by pressing the ENTER
button and UP/DOWN buttons to adjust selected field.
Rotate the FUNCTION SWITCH to AUTO. Your Camera will now
automatically take pictures whenever an animal is detected in range -based
on the default settings below
1
2
VIEWING PICTURES - USB
1. Plug provided USB cable into the USB port on your Windows
XP/Vista/Windows 7 or Macintosh computer.
2. Plug other end of USB cable into the camera’s USB port.
3. To access JPG pictures and AVI movie files, navigate to “My Computer” and
double click the “DCIM\100-MDGC” folder.
4. To exit USB mode, follow computer’s instructions for properly
disconnecting a removable drive and then unplug the USB cable from the
computer and the camera.
INFORMATION ON PICTURE
Time
Date
Function
Setting
Photo Quality
High
Photo Delay
after each photo is taken
1 minute
Multi Shot Count
1-Shot
MFH-DGS-L20
FUNCTION SWITCH DETAILS
AUTO MODE
The camera’s LCD screen will display the number of photos taken follow by the
pictures remaining when the FUNCTION SWITCH is set to AUTO. This is the
camera’s normal state for taking pictures. During this mode, the camera will
sleep and use a minimal amount of battery life. When the PIR motion sensor
detects an animal, it will wake up the camera and immediately take a picture.
When in AUTO MODE, press the ENTER button and the camera will
immediately take a picture.
DATE
The camera’s current date setting will be displayed by the LCD when the
FUNCTION SWITCH is set to DATE. Press the ENTER button and the Month
digits of the date will flash. Use the UP and DOWN buttons to adjust the
Month. Press the ENTER button to advance to the Day digits and repeat the
process. Press the ENTER button to set Year. Press the ENTER button to
confirm the new settings.
TIME
The camera’s current time setting will be displayed by the LCD when the
FUNCTION SWITCH is set to TIME. Press the ENTER button and the Hour
digits of the Time will flash. Use the UP and DOWN buttons to adjust the
hour. Press the ENTER button to advance to the Minute digits and repeat the
process. Press the ENTER button to set AM or PM. Press the ENTER button
again to confirm the new settings.
Pressing and holding the Up or Down Buttons will cause the digits to increase or
decrease at double speed.
Page 5
FUNCTION SWITCH DETAILS (cont.)
PHOTO QUALITY
The camera’s current PHOTO QUALITY setting will be displayed by the LCD
when the FUNCTION SWITCH is set to PHOTO QUALITY. Use the Up and
Down buttons to select the desired setting. Press the ENTER button to confirm
the new setting.
The Photo Quality settings are:
-
Low: 1280 x 960 (1.3MP)
-
High: 1600 x 1200 (2.0MP)
PHOTO DELAY
The camera’s current PHOTO DELAY setting will be displayed by the LCD
when the FUNCTION SWITCH is set to PHOTO DELAY. The camera will
wait a specified number of minutes between each picture. Use the UP and
DOWN buttons to select the desired setting. Press the ENTER button to
confirm the new setting.
The Photo Delay settings are:
-
1min
-
5min
-
10 min
-
30 min
-
60 min
MULTI-SHOT
The camera’s current MULTI-SHOT setting will be displayed by the LCD when
the FUNCTION SWITCH is set to MULTI-SHOT. The camera will
automatically take the specified number of photos, with a 5 second delay
between photos. Use the UP and DOWN buttons to select the desired setting.
Press the ENTER button to confirm the setting.
The Multi-Shot settings are:
-
1-Shot
- 2-Shots
DELETE ALL
The camera’s current DELETE ALL setting will be displayed by the LCD when
the FUNCTION SWITCH is set to DELETE ALL. This function will clear all
contents on the SD Card. Use the UP and DOWN buttons to select the desired
setting. Press the ENTER button to confirm the Delete All function.
