manualshive.com logo in svg

MOULDPRO TCU-200, Руководство пользователя

Поделиться
Скачать
MOULDPRO TCU-200 Скачать руководство пользователя страница 13

 

 

 

 

[13] 

User Guidelines 

– TCU-200 

 

12-06-2019 

Vers. 003 

 

5 

Installation 

Before starting the unit, the electrical and hydraulic connections have to be installed. The installation of  the 
unit has to be done in the order of the following chapters. After the proper installation, the unit is  ready to use.

 

DANGER

 

 

 

 

The temperature control unit must only be operated with water. Do not use 
solvents or other explosive substances such as petrol, toluene, etc. in the 
water.

 

 

CAUTION

 

 

 

 

When starting the unit without the prescribed connections the unit can be 
damaged.

 

Water quality 

– do not use water with chlorine addition.

 

 

NOTE

 

 

 

 

Observe the General Safety Information!

 

Before installing corresponding chapter of the manual should be read!

 

 

5.1 

Installing and dimensions of the temperature control unit 

 

The temperature control unit is designed for an ambient temperature of +10 up to 40°C. Sufficient  ventilation 
must be ensured during set-up. The distance between the temperature control unit and  other facilities must 
be at least 10cm. The ventilation opening must be free. 

  Check the unit of completeness and possible damages. 

  The unit has to be installed in a suitable location on even ground. It must be stand up right on the 

wheels (castors). 
 

  The unit is not protected against splash water and is not suitable for use in hazardous location. The 

unit must not be used in the open air. 

  The unit must not be transported lying down, transport in any other position than up right, will damage  

the unit. 

 

Содержание TCU-200











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды