MOULDPRO Flosense 4.0 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

P a g e

|

18

User Guidelines

– Flosense 4.0 Manifold 16-06-2020

Version 002

3.6.

Connecting the Manifold to the display

Once the manifold has been assembled and mounted, it can be connected to the Flosense

display, by using an M8 cable. The Manifold has one M8 connector on each side, but the

connector on the side which the arrow on the top plate is pointing towards is the one used

to connect to the manifold, as seen below.

After connecting the M8 cable to the manifold, connect the other side to the Flosense

display. Use an extension cable if necessary.

«
...
19
20
21
22
23
...
»

Содержание Flosense 4.0





























Отзывы:

Нет отзывов

Похожие инструкции для Flosense 4.0

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

Бренд: Jabra Страницы: 3

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: RAKwireless Страницы: 6

Бренд: Centurion Страницы: 16

Бренд: HW Group Страницы: 18

Бренд: SeaLevel Страницы: 115

Бренд: Case IH Страницы: 81

Бренд: Zencontrol Страницы: 2

Бренд: Gasboy Страницы: 119

Бренд: u-blox Страницы: 157

Бренд: Airlow Страницы: 20

RSF-B mini Series

Бренд: Harmonic Drive Страницы: 32

Бренд: Pilz Страницы: 32

Бренд: NuTone Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды