Motorola Nitro SLX 5000 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

background image

Figure 11: Ground Connection

Ground

3.8.2

Surge Protection

Unlike indoor CBSDs, outdoor CBSDs require a special surge protection.

The following areas require surge protection for Nitro CBSDs:

• AC surge protection – between the power mains and the AC/DC converter

• DC surge protection – between the AC/DC converter and the CBSD/ENB

• RF surge protection – between the CBSD/ENB and the antennas

• GPS Receiver surge protection – between the CBSD/ENB (assuming you are not directly mounting)

and the GPS antenna, and between the PTP server and the GPS antenna

• Ethernet surge protection – between the CBSD/ENB and the Ethernet switch and between the

CBSD/ENB and the fiber/copper media converter

NOTICE:

Motorola Solutions sells the surge protection devices appropriate for the installation. If

you want to use different surge protection devices, make sure they have a technical
specification equivalent to or better than the suggested hardware.

For the best hardware protection, all surge protectors must be installed according to best practice.
Refer to "Surge Protective Devices" in

Standards and Guidelines for Communication Sites R56

.

3.8.3

Preparing the SFP Cable for Connection

Prerequisites:

Ensure that:

• The SFP cable is approved for use by Motorola Solutions.

• LC Duplex cable assembly and SFP Transceiver are available and pre-assembled.

Figure 12: Pre-assembled LC Duplex Cable

Procedure:

1

Slide up and lift the clamp handle to open the housing lock.

MN007322A01-B
Chapter 3: SLX 5000 Installation

32

«
...
30
31
32
33
34
...
»

Содержание Nitro SLX 5000













































Отзывы:

Нет отзывов

Похожие инструкции для Nitro SLX 5000

EXPLORER 5075GX

Бренд: COBHAM Страницы: 78

Бренд: Novatel Страницы: 2

Бренд: CUSHCRAFT Страницы: 12

Бренд: Clas Ohlson Страницы: 4

Бренд: Maximum Страницы: 5

Бренд: Self-Sat Страницы: 6

Бренд: SELFSAT Страницы: 41

Бренд: Televes Страницы: 24

Бренд: Sirio Antenne Страницы: 2

Oyster CYTRAC DX Premium

Бренд: Ten-Haaft Страницы: 11

Бренд: Ten-Haaft Страницы: 44

Бренд: Ten Haft Страницы: 75

samy solar plus

Бренд: Ten-Haaft Страницы: 128

Бренд: Gogen Страницы: 20

Бренд: Hughes Страницы: 62

Xtreme HD8200XL

Бренд: Solid Signal Страницы: 9

DiRECWAY DW4000

Бренд: Hughes Network Systems Страницы: 50

Бренд: Hughes Network Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды