Motorola MVME172 Скачать руководство пользователя страница 267 | Manualshive

Страница: 267 / 354

background image

Programming Model

http://www.mcg.mot.com/literature

4-31

4

Programming the DMA Controllers

The IP2 chip implements four DMA channels. They can operate in the
standard or addressed mode. sDMA transfers must accommodate the I/O
port width. If the port width is 16 bits, then the byte count must be even; if
the width is 32 bits, then the byte count must be a multiple of four bytes.
The IP address counter must be initialized to zero before an sDMA transfer
is enabled. There are not any other restrictions placed on DMA operations.

Each DMAC has two modes of operation: command chaining, and direct.
In the direct mode, the local bus address, the IndustryPack address, the
byte count, and the control register of a DMAC are programmed and the
DMAC is enabled. The DMAC transfers data, as programmed, until the
byte count is zero, DMAEND is detected true as an input, or an error is
detected. When the DMAC stops, the status bits in the DMAC status
register are set and an interrupt is sent to the local bus master (if the
DMACs interrupts are enabled). Multiple DMAC commands can be
automatically invoked using the command chaining mode.

In the command chaining mode, a singly-linked list of commands is built
in local memory and the table address register in the DMAC is
programmed with the starting address of the list of commands. The DMAC
control register 1 is programmed and the DMAC is enabled. The DMAC
executes commands from the list until all commands are executed or an
error is detected. When the DMAC stops, the status bits are set in the
DMAC status register and an interrupt is sent to the local bus master (if the
DMAC interrupts are enabled). Additionally, when the DMAC finishes
processing a command in the list, and interrupts are enabled for that
command, the DMAC sends an interrupt to the local bus master if its
interrupts are enabled.

Note that when the DMA register context is updated for the next command
packet, a DMA function is used. The state of the snoop control signals for
this DMA function is determined by the settings of jumper J26 (as is the
state of the snoop control signals for all other DMA cycle types). Refer to
the Hardware Preparation section of your MVME172 installation and use
manual.

«
...
265
266
267
268
269
...
»

Содержание MVME172



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MVME172

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Abus Страницы: 12

Бренд: Badger Basket Страницы: 3

Бренд: BADLANDS Страницы: 2

Бренд: Laars Страницы: 28

Бренд: LANGER EMV-Technik Страницы: 48

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды