manualshive.com logo in svg

Motorola MVME172, Руководство программиста

Motorola MVME172 - процессорная плата для встраиваемых систем. Вы можете загрузить бесплатное Руководство по программированию и обслуживанию с нашего сайта. Это дает вам всю необходимую информацию для эффективной работы с устройством. Скачать данный документ вы можете с manualshive.com.

Поделиться
Скачать
background image

LCSR Programming Model

http://www.mcg.mot.com/literature

2-27

2

A VMEbus slave map decoder is programmed by loading the starting 
address of the segment into the starting address register and the ending 
address of the segment into the ending address register. If the VMEbus 
address modifier codes indicate an A24 VMEbus address cycle, then the 
upper eight bits of the VMEbus address are forced to zero before the 
compare. The address modifier select register should be programmed for 
the required address modifier codes. A VMEbus slave map decoder is 
disabled when the address modifier select register is cleared. 

The address translation registers allow local resources to have different 
VMEbus and local bus addresses. Only address bits A31 through A16 may 
be modified. 

The address translation registers also provide the upper eight local bus 
address lines when an A24 VMEbus cycle is used to accesses a local 
resource. The address translation register should be programmed with the 
translated address and the address translation select register should be 
programmed to enable the translated address. If address translation is not 
desired, then the address translation registers should be programmed to 
zero. 

The address translation address register and the address translation select 
register operate in the following way: If a bit in the address translation 
select register is set, then the corresponding local bus address line is driven 
from the corresponding bit in the address translation address register. If the 
bit is cleared in the address translation select register, then the 
corresponding local bus address line is driven from the corresponding 
VMEbus address line. The most significant bit of the address translation 
select register corresponds to the most significant bit of address translation 
register and to A32 of the local bus and A32 of the VMEbus. 

In addition to the address translation method previously described, the 
VMEchip2 used on the MVME166/167/187 includes an adder which can 
be used for address translation. When the adder is enabled, the local bus 
address is generated by adding the offset value to the VMEbus address 
lines VA<31..16>. The offset is the value in the address translation/offset 
register. If the VMEbus transfer is A24, then the VMEbus address lines 
VA<31..24> are forced to 0 before the add. The adders are enable by 
setting bit 11 for map decoder 1 and bit 27 for map decoder 2 in register 

Содержание MVME172



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MVME172

Valve Concepts 5400 Installation, Operation And Maintenance Manual preview
5400
Бренд: Valve Concepts Страницы: 16
Canon BU-51H Remote Control Manual preview
BU-51H
Бренд: Canon Страницы: 2
Hardi HC5500 Quick Manual preview
HC5500
Бренд: Hardi Страницы: 2
YASKAWA CC-Link Technical Manual preview
CC-Link
Бренд: YASKAWA Страницы: 64
V2 Phoenix Programming Manual preview
Phoenix
Бренд: V2 Страницы: 3
Unitech RM300 SDK User Manual preview
RM300 SDK
Бренд: Unitech Страницы: 11
B meters IWM-PL4 Quick User Manual preview
IWM-PL4
Бренд: B meters Страницы: 10
IFM CR710S Original Operating Instructions preview
CR710S
Бренд: IFM Страницы: 49
National Instruments PXIe-4302 Calibration Procedure preview
PXIe-4302
Бренд: National Instruments Страницы: 14
National Instruments PXIe-4302 User Manual preview
PXIe-4302
Бренд: National Instruments Страницы: 31
National Instruments NI-9244 User Manual And Specifications preview
NI-9244
Бренд: National Instruments Страницы: 50
National Instruments NI 9870 Operating Instructions And Specifications preview
NI 9870
Бренд: National Instruments Страницы: 24
National Instruments NI 9247 Getting Started Manual preview
NI 9247
Бренд: National Instruments Страницы: 21
National Instruments NI 9242 Getting Started Manual preview
NI 9242
Бренд: National Instruments Страницы: 39
National Instruments NI 9218 Getting Started preview
NI 9218
Бренд: National Instruments Страницы: 22
National Instruments NI 9263 Calibration Procedure preview
NI 9263
Бренд: National Instruments Страницы: 8
National Instruments NI 9425 Getting Started Manual preview
NI 9425
Бренд: National Instruments Страницы: 20
National Instruments NI 9234 Getting Started preview
NI 9234
Бренд: National Instruments Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды