Motorola MPC821FADS страница 34 Скачать руководство пользователя

Страница: 34 / 54

Signal Descriptions

5-20

MPC821FADS-DB USER’S MANUAL

MOTOROLA

MODCK1

I/O

Mode Clock 1 signal. OP2/MODCK1/STS on

the MPC821. Used at power-on reset.

GND

—

RESETA

I,H

Reset signal for PCMCIA port A.

GND

—

BADDR28

I/O,X

Burst Address line 28. Dedicated for external

master support. Used to generate a burst

address during external master burst cycles.

Pulled up, but otherwise unused on this board.

GND

—

TEXP

X,X

Timer Expired signal. Not used on this board.

GND

—

WAIT_B

I/O, L

Wait signal for PCMCIA Slot B. Pulled up, but

otherwise unused on this board.

GND

—

MODCK2

I/O

Mode Clock 2 signal. OP3/MODCK2/DSDO on

the MPC821. Used at power-on reset as

MODCK2 and configured afterwards as OP3.

This signal can be configured for another

function.

GND

—

Not connected.

GND

—

SRESET

I/O, L, OD

Soft Reset signal. This signal is driven by

onboard logic and may be driven by offboard

logic with open-drain gate only.

GND

—

PORST

X, L

Power-On Reset signal. Not used on the

MPC8xxFADS, but generated on the

daughterboard.

GND

—

HRESET

I/O, L, OD

Hard Reset signal. This signal is driven by

onboard logic and may be driven by offboard

logic with open-drain gate only.

GND

—

Table 5-10. PM2 Interconnect Signals (Continued)

PIN

MOTHERBOARD

SIGNAL

DAUGHTERBOARD

SIGNAL

INPUT/

OUTPUT

DESCRIPTION

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

IVE

D B

Y F

Содержание MPC821FADS























































Результаты поиска

Содержание MPC821FADS

Отзывы:

Похожие инструкции для MPC821FADS

Бренды по названию

Популярные бренды

Motorola MPC821FADS, Руководство пользователя

Результаты поиска

Содержание MPC821FADS

Отзывы:

Похожие инструкции для MPC821FADS

Бренды по названию

Популярные бренды