SCALE CALIBRATION (MODELS WITH A SCALE ONLY)
4 - 3
Step 1 - Electronic Entry into Calibration Mode
Encompasses all scales sold
without
a mechanical calibration switch installed. When the integrated scale
does not have a calibration switch, electronic entry is required.
Firmware Versions Older Than v3.4
To perform an electronic calibration entry:
•
Touch
Scale Zero
and
Volume/Tone
simultaneously for five consecutive seconds (see
for the location of these buttons on the front panel).
Firmware Versions Newer Than v3.4
To perform an electronic calibration entry:
•
Press and hold the
Scale Zero
and
Volume
buttons continuously for five seconds. After five seconds a
short beep sounds. Release the
Scale Zero
and
Volume
buttons.
•
Within two seconds after releasing the buttons, press the
Scale Zero
and
Volume
buttons again and
release. After release the system sounds five long beeps and enters scale calibration.
When Calibration Mode is entered successfully, the scanner emits five long beep sounds. The optional Scale
Display blinks
CAL00
and
CAL _ _
and the 7-segment display scrolls
C00Lb
, or
C00g
. Once the scale
Calibration Mode is successfully entered, continue the Calibration process with
.
Step 2 - Program Legal Parameters
Sealable and legal parameters (
Unit Selection
and
Dampening Filter Setting
) can only be
programmed/changed when the MP6000 is placed into Calibration Mode. There is no requirement to change
these values (they can remain in the default or present state). However, if there is a need to change their
values they must be programmed when the scale is in a Calibration Mode. The
Dampening Filter Setting
can
be changed multiple times during a Calibration Mode without affecting the calibration outcome.
After completing these changes, the calibration process re-starts with
Step 3 - Calibration at NO LOAD on
. If you change the
Unit Selection
value before successfully reaching
Step 5 - Calibration Success or
and the Calibration Mode exits, the scale will be non-operational. The scale will have to be
successfully calibrated before it becomes operational.
Legal Scale Units (Unit Selection) - Kilograms or Pounds
To change the legal parameter
Unit Selection
(when the scale is in a Calibration Mode):
1.
Verify the units of weight measurement by checking the
Scale Display
icon (the icon displays either
lb
or
kg
units), or the 7-segment display which scrolls either
Lb
or
g
units (
g
indicates kg units).
IMPORTANT
If Calibration Mode was not entered successfully, the scale remains in its current state.
Содержание MP6000
