manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Справочное руководство

Серия процессоров Motorola M-CORE MMC2001 – идеальное решение для повышения производительности вашего устройства. Скачайте бесплатно руководство по эксплуатации (Reference Manual) с нашего сайта. Получите все необходимые инструкции для эффективного использования продукта. {Website} – ваш источник полезной информации.

Поделиться
Скачать
background image

MMC2001

ROM MODULE

MOTOROLA 

REFERENCE MANUAL

5-1 

SECTION 5

ROM MODULE

5.1 Overview

The ROM module provides 256 Kbytes of general-purpose code and data storage.

5.2 Functional Description

The 256-Kbyte ROM module supports byte, halfword, and word read accesses with a
32-bit data interface to the CPU. Only the requested bytes are guaranteed to be valid
on accesses. Write cycles that are attempted to the ROM address space are termi-
nated with a TEA response to the CPU.

The ROM module base address is located at address 0x0000 0000 when the module
is enabled. Echoing of the ROM block occurs throughout the region 0x0004 0000 –
0x000F FFFF; no attempt is made to detect this condition. Accesses in the range of
0x0010 0000 – 0x0FFF FFFF result in TEA termination to the CPU.

Software designers should be aware that the echoing characteristics of this imple-
mentation may change for future versions of the M•CORE family.

External control is provided to disable the on-chip ROM for system debugging pur-
poses via a control input to the chip. When asserted, the MOD input signal causes
the on-chip ROM to be disabled for the initial program counter fetch out of reset, and
the chip select module to dedicate the CS0 output for an external boot ROM. Refer to
SECTION 4 SIGNAL DESCRIPTIONS and SECTION 7 EXTERNAL INTERFACE
MODULE for details of the interaction of the MOD input signal with the CS0 signal.

Table 5-1 ROM Module Address Map

Address

Use

Access

00000000

to

0003FFFF

ROM Array

00000001 to 00000003 are used as off-chip boot 

vectors when the MOD signal is asserted

Supervisor, 

Selective User

00040000

to

000FFFFF

ROM echoes on 256-Kbyte boundaries

Supervisor, 

Selective User

00100000

to

0FFFFFFF

Not Used (Access causes transfer error)

Not Applicable

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Содержание M-CORE MMC2001 Series




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-CORE MMC2001 Series

3Ware 9000 Series Specification preview
9000 Series
Бренд: 3Ware Страницы: 2
wattio AIR Read Me preview
AIR
Бренд: wattio Страницы: 20
Panasonic FP-I4C User Manual preview
FP-I4C
Бренд: Panasonic Страницы: 31
Panasonic EYFR03 Training Manual preview
EYFR03
Бренд: Panasonic Страницы: 31
NAiS FP Series Hardware Manual preview
FP Series
Бренд: NAiS Страницы: 199
Panasonic CZ-ANC2 Instruction Manual preview
CZ-ANC2
Бренд: Panasonic Страницы: 38
Panasonic CZ-256ESMC3 Quick Reference preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 36
Panasonic CZ-256ESMC3 Technical Data Manual preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 179
Panasonic AW-RP60G Operating Manual preview
AW-RP60G
Бренд: Panasonic Страницы: 23
C Prox Ltd FP1 User Manual preview
FP1
Бренд: C Prox Ltd Страницы: 5
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Бренд: Federal Signal Corporation Страницы: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Бренд: FASTRON. Страницы: 16
Parker A4W Series Installation And Service Information preview
A4W Series
Бренд: Parker Страницы: 12
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Бренд: IBC Страницы: 8
Altronix Trove T1VK3F4 Installation Manual preview
Trove T1VK3F4
Бренд: Altronix Страницы: 8
nvent JBS-100-EC Installation Instructions Manual preview
JBS-100-EC
Бренд: nvent Страницы: 6
Teledyne THCD-401 Instruction Manual preview
THCD-401
Бренд: Teledyne Страницы: 47
Western Co WMarine10 Technical Manual preview
WMarine10
Бренд: Western Co Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды