manualshive.com logo in svg

Motorola DSP56309, Руководство пользователя

Motorola DSP56309 - процессор с сигнальной обработкой, идеальный для аудио и видео приложений. Здесь вы можете загрузить бесплатный пользовательский мануал для оптимальной настройки и использования устройства. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Triple Timer Module

Timer Operational Modes

MOTOROLA

DSP56309UM/D 9-19

If the counter overflows, the TOF bit is set, and if TOIE is set, an overflow interrupt is 
generated.

The counter contents can be read at any time by reading the TCR.

9.4.1.3

Timer Toggle (Mode 2)

In this mode, the timer periodically toggles the polarity of the TIO signal.

Set the TE bit in the TCR to clear the counter and enable the timer. The value to which 
the timer is to count is loaded into the TPCR. The counter is loaded with the TLR value 
when the first timer clock signal is received. The TIO signal is loaded with the value of 
the INV bit. The timer clock signal can be taken from either the DSP56309 clock divided 
by two (CLK/2) or from the prescaler clock output. Each subsequent clock signal 
increments the counter. 

When the counter value matches the value in the TCPR, the polarity of the TIO output 
signal is inverted. The TCF bit in the TCSR is set and a compare interrupt is generated if 
the TCIE bit is set. 

If the TRM bit is set, the counter is loaded with the value of the TLR when the next timer 
clock is received, and the count is resumed. If the TRM bit is cleared, the counter 
continues to be incremented on each timer clock.

This process is repeated until the TE bit is cleared, disabling the timer. The counter 
contents can be read at any time by reading the TCR.

The TLR value in the TCPR sets the delay between starting the timer and toggling the 
TIO signal. To generate output signals with a delay of X clock cycles between toggles, 
the TLR value should be set to X/2, and the TRM bit should be set.

This process is repeated until the timer is disabled (i.e., TE is cleared). If the counter 
overflows, the TOF bit is set, and if TOIE is set, an overflow interrupt is generated.

The counter contents can be read at any time by reading the TCR.

Bit Settings

Mode Characteristics

TC3

TC2

TC1

TC0

TIO

Clock

#

Function

Name

0

0

1

0

Output

Internal

0

Timer

Toggle

Содержание DSP56309










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSP56309

Love Controls Loop Alarm Installation Instructions Manual preview
Loop Alarm
Бренд: Love Controls Страницы: 8
VALMETAL 01A99-0200 Operators Manual And Parts Lists preview
01A99-0200
Бренд: VALMETAL Страницы: 38
Prima PFP720 User Manual preview
PFP720
Бренд: Prima Страницы: 7
Toastmaster TFP2 Use And Care Manual preview
TFP2
Бренд: Toastmaster Страницы: 14
Wheatstone Corporation VP-8IP Technical Manual preview
VP-8IP
Бренд: Wheatstone Corporation Страницы: 240
Bravetti QUAD BLADE FOOD PROCESSOR BP101H3 Owner'S Manual preview
QUAD BLADE FOOD PROCESSOR BP101H3
Бренд: Bravetti Страницы: 6
Kogan THERMOBLEND ELITE KAPRETHBLNA Quick Start Manual preview
THERMOBLEND ELITE KAPRETHBLNA
Бренд: Kogan Страницы: 20
Sage the Kitchen Wizz Pro SFP800 Quick Manual preview
the Kitchen Wizz Pro SFP800
Бренд: Sage Страницы: 128
TC Electronic DB8 MKII Hardware Installation Manual preview
DB8 MKII
Бренд: TC Electronic Страницы: 16
IEI Technology PCISA-6770E2-RS Quick Installation Manual preview
PCISA-6770E2-RS
Бренд: IEI Technology Страницы: 12
LD LD X223 User Manual preview
LD X223
Бренд: LD Страницы: 76
Haier HFP400SS - Food Processor, With User Manual preview
HFP400SS - Food Processor, With
Бренд: Haier Страницы: 16
Bosch MCM3 Series MultiTalent 3 Instruction Manual preview
MCM3 Series MultiTalent 3
Бренд: Bosch Страницы: 193
Bosch MAS40 series Instruction Manual preview
MAS40 series
Бренд: Bosch Страницы: 86
Bosch MCM 5000 UC Owner'S Manual preview
MCM 5000 UC
Бренд: Bosch Страницы: 28
Bosch MCM3200 Instruction Manual preview
MCM3200
Бренд: Bosch Страницы: 193
Bosch MCM3...AU Instruction Manual preview
MCM3...AU
Бренд: Bosch Страницы: 24
Bosch CreationLine MUM58243 Instruction Manual preview
CreationLine MUM58243
Бренд: Bosch Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды