Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 295 | Manualshive

Страница: 295 / 550

background image

Chapter 13. Physical Layer Interface Controller (PLIC)

13-1

Chapter 13
Physical Layer Interface Controller
(PLIC)

This chapter provides detailed information about the MCF5272’s physical layer interface
controller (PLIC), a module intended to support ISDN applications. The chapter begins
with a description of operation and a series of related block diagrams starting with a
high-level overview. Each successive diagram depicts progressively more internal detail.
The chapter then describes timing generation, the programming model, and concludes with
three application examples.

The reader is assumed to have a basic familiarity with ISDN technology and terminology.
A glossary containing many ISDN terms can be found on the web at the following URL:
http://www.tribecatech.com/isdnterm.htm.

13.1 Introduction

The physical layer interface controller (PLIC) allows the MCF5272 to connect at a physical
level with external CODECs (coder/decoder) and other peripheral devices that use either
the general circuit interface (GCI) or interchip digital link (IDL) physical layer protocols.
This module is primarily intended to facilitate designs that include ISDN (integrated
services digital network) interfaces.

The MCF5272 has four dedicated physical layer interface ports for connecting to external
ISDN transceivers, codecs, and other peripherals. There are three sets of pins for these
interfaces. Port 0 has its own dedicated set of pins. Ports 1, 2, and 3 share a set of pins.
Port 3 can also be configured to use a dedicated pin set. Ports 1, 2, and 3 always share the
same data clock (DCL).

When the ports are operated in slave mode, the PLIC can support a DCL frequency of
4.096 MHz and frame sync frequency (FSC/FSR) of 8 KHz. When in master mode, DCL
should be no greater than one-twentieth of the CPU clock (CLKIN), with a maximum
FSC/FSR of 8 KHz.

This chapter is written from the perspective of connecting to an ISDN transceiver with
8-KHz frame sync. The MCF5272 PLIC has four ports, port 0 – port 3, connected through
three pin sets, numbered 0, 1, and 3. A port can service, read, or write any 2B + D channel.
As shown in Figure 13-1, port 0 connects through pin set 0, and ports 1 and 2 both connect

«
...
293
294
295
296
297
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

Бренд: Tandy Страницы: 24

Бренд: Infoblox Страницы: 13

Бренд: Teletronics International Страницы: 57

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

Бренд: Xcellon Страницы: 24

i.LON SmartServer

Бренд: Echelon Страницы: 34

Бренд: ADLINK Technology Страницы: 95

NexXxoS GPX-N 1070-M08

Бренд: Alphacool Страницы: 4

EK-Quantum Vector TUF RX 6800

Бренд: ekwb Страницы: 14

STM32MP157 Series

Бренд: ST Страницы: 47

SATA II-150 PCI

Бренд: SIIG Страницы: 16

Бренд: Paradyne Страницы: 46

Бренд: Lanner Страницы: 43

Бренд: ADLINK Technology Страницы: 34

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренд: Airaya Страницы: 28

JNLH61S-6C Series

Бренд: JETWAY Страницы: 36

593/25, 593/45, 593/TB, RS-422, RS-485

Бренд: Patton electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды