Important
Do not place your CT100 in the bathroom or other humid areas.
Location
You need to place your CT100 base within reach of the telephone wall socket
so that the cable will reach. The socket-outlet should be installed near the
equipment and should be easily accessible.
If you are wall mounting your phone please refer to the wall mount template
over the page.
Connecting the handset and base
1. Plug one end of the handset curly cord into the socket marked
on the
underside of the base and the other end into the socket at the bottom of
the handset.
2. Plug the telephone line cord into the socket marked
.
Overview of your handset
A Earpiece
To listen to your caller.
B Microphone
To speak to your caller.
C Curly cord socket
Where you plug in your curly cord.
Box Contents
Getting started
Getting started
Help
General information
Overview of the base
A Hook switch
Hangs up a call when pressed or when you replace the handset.
B Mute
Speak to someone nearby without your caller hearing the conversation.
C R
Recall used with switchboards / PABX.
When on an external call, press to access a Call Waiting Line when a call
waiting prompt signal is heard. Press again to toggle between the two
calls.
D Redial
Press to redial the last number called.
E Pause
Press to enter a pause (P) when dialling numbers.
F Ringer switch
Change the ringer volume.
Using the phone
Getting started
A
B
C
F
A
B
C
D
E
3.1 Calls
3.1.1
Make a call
Lift the handset, when you hear the dial tone, dial the number.
3.1.2
End a call
Place the handset back on the base.
3.1.3 Receive a call
Lift the handset to answer the call.
3.2 Mute
You can mute your handset so that you can talk to someone nearby without
your caller hearing.
1. During a call, press and hold
.
2. Release
again to resume your call.
3.3 Redial
The last entry dialled is stored in the phone; the number can be up to 31 digits
long.
To redial the last entry called, pick up the handset and press
.
3.4
Ringer volume control
Switch the ringer volume between high (left) normal (middle) and low (right).
3.5 Recall
Recall is useful to access certain network services and PABX /switchboard
services.
For more information about network services contact your network operator.
The recall mode preset in the CT100 is suitable for your country network.
No dial tone
• Use only the telephone line cord supplied.
• Check that the telephone line cord is connected properly.
Important
This product is intended for connection to analogue public switched
telephone networks and private switchboards in Singapore.
Important safety instructions
Follow these safety precautions when using your phone to reduce the risk of
fire, electric shock, and injury to persons or property:
• Do not set the phone on a heating register or over a radiator. Ensure that
proper ventilation is provided at the installation site.
• Do not use while wet or while standing in water.
• Do not use this product near water (for example, near a bath tub, kitchen
sink, or swimming pool).
• Do not disassemble this product. If service or repair work is required,
contact the customer service helpline found in this User Guide.
• Avoid using during an electrical storm. Use a surge protector to protect
the equipment.
Installation Guidelines
• Read and understand all instructions and save them for future reference.
• Follow all warnings and instructions marked on the product.
• Do not install this product near a bath tub, sink, or shower.
• Do not place this product on an unstable cart, stand, or table. This
product may fall, causing serious damage to the product.
• Adjust only those controls that are covered by the operating instructions.
Improper adjustment of other controls may result in damage and will
often require extensive work to restore the product to normal operation.
Corded base
Corded handset
Quick start
guide
Telephone line
cord
Curly cord
Quick Start Guide
This Quick Start Guide provides all the information you
need to get you started.
Alternatively, contact Customer Services on:
6278 8274
Email: [email protected]
Motorola CT100
Corded Telephone
