Motorola APX8500 Скачать руководство пользователя

Страница: 258 / 273

NEXT >

< PREV

CONTENTS

UTILITIES

(continued)

258

Using Permanent Horn and Lights

If Permanent Horn and Lights are enabled, horn and
lights will automatically turn on when the radio
powers up.

Procedure:

Press the

Menu Select

button directly below

H/L

once to turn off the alarm(s).

Press the

Menu Select

button directly below

H/L

momentarily to enable the last selected alarm(s).

The display briefly shows the enabled alarms,
and then reverts back to the selected mode.

Changing the Selected Alarms

Procedure:

Press the

Menu Select

button directly below

H/L

until the display shows the required alarm.

Press the

Menu Select

button directly below

H+L

to turn on both horn and lights.

The display shows

Horn/Lites on

Press the

Menu Select

button directly below

Lgts

to turn on the lights.

The display shows

Lights on

Press the

Menu Select

button directly below

Horn

to turn on the horn.

The display shows

Horn on

Off

entry is shown at the soft-key when one of

the features above is active.

Selecting the

Off

deactivates the current active

alarm.

Содержание APX8500


















































































































































































































































































Результаты поиска

Содержание APX8500

Отзывы:

Похожие инструкции для APX8500

Бренды по названию

Популярные бренды

Motorola APX8500, Руководство пользователя

Результаты поиска

Содержание APX8500

Отзывы:

Похожие инструкции для APX8500

Бренды по названию

Популярные бренды