Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 267 / 526

background image

Chapter 1 Introduction

This manual contains information needed for Levels One and Two radio servicing. Level One
servicing consists of radio programming, radio alignment, knobs replacement, and installation and
removal of the antenna, belt clip, battery, and universal connector cover. Level Two servicing covers
disassembly and reassembly of the radio to replace circuit boards.

1.1

Manual Contents

Included in this manual is radio specification for the 900 MHz (896–941 MHz) frequency bands, a
general description of ASTRO APX1000 models, recommended test equipment, service aids, radio
alignment procedures, general maintenance recommendations, procedures for assembly and
disassembly, and exploded views and parts lists.

1.2

Notations Used in This Manual

Throughout the text in this publication, you will notice the use of note, caution, warning, and danger
notations. These notations are used to emphasize that safety hazards exist, and due care must be
taken and observed.

NOTE:

An operational procedure, practice, or condition that is essential to emphasize.

CAUTION indicates a potentially hazardous situation which, if
not avoided, might result in equipment damage.

WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or injury.

DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death or
injury.

!

C a u t i o n

«
...
265
266
267
268
269
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: GOWIN Страницы: 2

Бренд: ELBE Страницы: 2

aXis CONTROLLER

Бренд: Champion Страницы: 45

Бренд: Grundig Страницы: 8

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 5

Бренд: G-project Страницы: 14

Бренд: Grace Digital Страницы: 52

Бренд: K&S BASIC Страницы: 13

MrSteam CU Series

Бренд: Sussman Страницы: 34

Бренд: ulsonix Страницы: 4

Бренд: Richter Страницы: 12

Бренд: Virgin Страницы: 2

Бренд: QFX Страницы: 3

Бренд: GE Страницы: 88

Бренд: JRC Страницы: 4

Бренд: Noblex Страницы: 15

Бренд: ION Страницы: 32

Бренд: Motorola Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды