Motorola APX 4000 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 526

background image

Disassembly/Reassembly Procedures

: Serviceable Components of the Main Sub-Assemblies

8-15

8.4.6

Removal of the Front Kit Assembly (A)

1. Complete the steps in

Section 8.4.5.1.

and

Section 8.4.5.5.

Section 8.4.5.7.

2. With the steps completed, the Front Kit Assembly (A) is obtained.

8.5

Serviceable Components of the Main Sub-Assemblies

8.5.1

Servicing Main Board Assembly

Figure 8-22. Serviceable Components – Main Board Assembly

8.5.1.1 Servicing Coin Cell:

1. Complete steps from

Section 8.4.5.1.

through

Section 8.4.5.3.

2. Remove the coin cell with the Black Stick.

NOTE:

Make sure the positive side is facing upwards.

3. Press the new coin cell into the battery carrier until it is secured and fully snapped into place.

8.5.1.2 Servicing Thermal Pad:

1. Complete steps from

Section 8.4.5.1.

through

Section 8.4.5.3.

2. Carefully peel off the pad.
3. Ensure there is no debris or residue left on the amplifier’s surface.
4. Replace with new Thermal Pad.
5. Peel the liner off the new pad and place in the respective location. Make sure the bottom

surface of the pad is mating with the top surface of the amplifier.

6. Apply slight pressure to activate the adhesive.

Thermal pad should always be replaced when the Main board
assembly is removed.

Coin Cell

Thermal Pad

!

C a u t i o n

«
...
107
108
109
110
111
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Barrett Страницы: 30

Бренд: CA Страницы: 6

Бренд: IDT Страницы: 13

Бренд: QFX Страницы: 6

Бренд: Hytera Страницы: 22

Бренд: Generac Power Systems Страницы: 116

Бренд: Sandstrom Страницы: 36

Бренд: Generac Power Systems Страницы: 36

Бренд: Westinghouse Страницы: 100

Бренд: JD Williams Ltd. Страницы: 20

Musik Boy 50L RP 5240 LW

Бренд: Grundig Страницы: 8

Бренд: Yaesu Страницы: 3

Бренд: Onan Страницы: 28

Бренд: Hytera Страницы: 9

Бренд: BRIGHT Страницы: 69

Бренд: Uniden Страницы: 72

Бренд: Acterna Страницы: 40

Бренд: perfect pro Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды