Motorola APX 1000 Скачать руководство пользователя

Страница: 75 / 136

2.7.3

Sending an Emergency Alarm

When and where to use:

This feature allows you to send a data transmission, which identifies the

radio sending the emergency, to the dispatcher.

NOTICE:

The default timer of

Emergency

button press to activate Emergency is 50

milliseconds. This timer is programmable from 50–6200 milliseconds by a qualified technician.

Procedure:

Press the preprogrammed

Emergency

button.

One of the following scenarios occurs:

• The display shows

Emergency

and the current zone or channel. You hear a short medium-

pitched tone and the LED blinks red momentarily.

• The radio sounds a short low-pitched tone to indicate that the selected channel does not

support emergency and rejects to launch emergency mode. The display shows

emergency

, if the selected channel does not support emergency.

When you receive the dispatcher’s acknowledgment, the display shows

Ack received

. Four tones

sound, the alarm ends, and the radio exits the Emergency Alarm mode.

If no acknowledgment is received, the display shows

No acknowledge

. The alarm ends when the

timer expires and the radio exits the Emergency Alarm mode.

2.7.4

Sending an Emergency Call (Trunking Only)

When and where to use:

This feature gives your radio priority access to a talkgroup.

Procedure:

Press the preprogrammed

Emergency

button.

One of the following scenarios occurs:

• The display shows

Emergency

on the current zone and channel. You hear a short medium-

pitched tone and the LED blinks red momentarily.

• You hear the radio sounds a short low-pitched tone to indicate the selected channel does not

support emergency and rejects to launch emergency mode.

Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.

Press and hold the

PTT

button. Speak clearly into the microphone.

Release the

PTT

button to end the transmission and wait for a response from the dispatcher.

To exit Emergency Call, press and hold the preprogrammed

Emergency

button for about a

second.

2.7.5

Sending An Emergency Call With Hot Mic (Trunking Only)

This feature allows you to send an Emergency Call with hot mic to a group of radios.

When and where to use:

Your radio must be programmed for this type of operation.

MN000255A01-BL

Chapter 2: Advanced Features

Содержание APX 1000








































































































































Результаты поиска

Содержание APX 1000

Отзывы:

Похожие инструкции для APX 1000

Бренды по названию

Популярные бренды

Motorola APX 1000, Руководство пользователя

Результаты поиска

Содержание APX 1000

Отзывы:

Похожие инструкции для APX 1000

Бренды по названию

Популярные бренды