background image

Vanguard 300/305 Operator's Guide 

Notice 

1995 Motorola Inc. 
20 Cabot Boulevard 
Mansfield, Massachusetts 02048 
(508) 261-4000 
All rights reserved 
Printed in U.S.A. 

Restricted Rights Notification for U.S. Government Users  

The software (including firmware) addressed in this manual is provided to the 
U.S. Government under agreement which grants the government the minimum 
"restricted rights" in the software, as defined in the Federal Acquisition 
Regulation (FAR) or the Defense Federal Acquisition Regulation Supplement 
(DFARS), whichever is applicable. 

If the software is procured for use by the Department of Defense, the following 
legend applies: 

Restricted Rights Legend 

Use, duplication, or disclosure by the Government is subject to restrictions as set 
forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer 
Software clause at DFARS 252.227-7013. 

If the software is procured for use by any U.S. Government entity other than the 
Department of Defense, the following notice applies: 

Notice 

Notwithstanding any other lease or license agreement that may pertain to, or 
accompany the delivery of, this computer software, the rights of the Government 
regarding its use, reproduction, and disclosure as set forth in FAR 52.227-19(C). 

Unpublished - rights reserved under the copyright laws of the United States. 

Proprietary Material 

Information and software in this document are proprietary to Motorola Inc. (or its 
Suppliers) and without the express prior permission of an officer of Motorola Inc., 
may not be copied, reproduced, disclosed to others, published, or used, in whole 
or in part, for any purpose other than that for which it is being made available. 
Use of software described in this document is subject to the terms and conditions 
of the Motorola Software License Agreement. 

This document is for information purposes only and is subject to change without 
notice. 

Содержание 68230 - Vanguard 300 DSU/CSU
















































































Отзывы: