manualshive.com logo in svg

MotorGuide TOUR 109, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Поделиться
Скачать
MotorGuide TOUR 109 Скачать руководство пользователя страница 70

IMPORTANT: Trolling motors stored in temperatures below 0 °C (32 °F) should

be operated slowly for a minimum of 15 minutes before going above 30%

operation.

Lubrication Points

NOTE: Preferred lubricants can be obtained at any authorized MotorGuide or

Mercury Marine service center.

To reduce friction and quiet squeaks, lubricate the specified locations

periodically with the following lubricants:

•

Latch hooks ‑ 2‑4‑C with PTFE

•

Latch strikers ‑ 2‑4‑C with PTFE

•

Pivot pins ‑ 4‑Stroke 10W‑30 Outboard Oil

IMPORTANT: Never use an aerosol lubricant to grease or oil any part of the

unit. Many aerosol lubricants contain harmful propellants that can cause

damage to various parts of the trolling motor.

a -

Latch hooks

b -

Latch strikers

c -

Pivot pins

Tube Ref

No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Latch pins, latch hooks

92-802859A 1

110

4-Stroke 10W-30

Outboard Oil

Pivot pins

92-8M0078625

Battery Inspection

The battery should be inspected at periodic intervals to ensure proper trolling

motor operation.
IMPORTANT: Read the safety and maintenance instructions which accompany

your battery.

1. Ensure that the battery is secured to the vessel.
2. Ensure that the battery cable terminals are clean, tight, and correctly

installed. For installation instructions, refer to 

Battery Connection

.

3. Ensure that the battery is equipped with a battery box to prevent

accidental shorting of the battery terminals.

70026

a

a

b

b

c

MAINTENANCE

  

64

eng

Содержание TOUR 109













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды