MOTO GUZZI V85 E4 Скачать руководство пользователя страница 94

Страница: 94 / 108

•

Remove the small ends from the con-

necting rods.

CAUTION

REPEAT THE PROCEDURE FOR THE OTHER CONNECT-
ING ROD

Inspecting the crankcase halves

•

Check that the mating faces are not damaged, dented or scored. Remove the liquid gasket

residues.

•

Check that the threads of the stud bolts are not dented or stripped; if they are, replace the

stud bolt or stud bolts.

•

Blow all oil galleries of the two crankcase halves with compressed air.

Inspecting the crankshaft components

•

Smear the thread of the cap with threadlocker and tighten the cap firmly.

•

Blow with compressed air to clean the lubrication passage seats.

CAUTION

THE CRANKSHAFT IS NITRIDED AND CANNOT BE GROUND; IF WORN, TAPERED OR DEEPLY
SCORED, THE CRANKSHAFT MUST BE REPLACED

RANKSHAFT

CHECK

- L

IMIT

VALUES

Specification

Desc./Quantity

Main journal diameter on timing system side (WEAR LIMIT

VALUE)

40.004 mm (1.5750 in)

Main bushing seat diameter on timing system side (MAXIMUM

WEAR VALUE)

43.67 mm (1.7193 in)

Thickness for main bushing on timing system side (MAXIMUM

WEAR VALUE)

1.805 mm (0.0711 in)

Main journal diameter on clutch side (MINIMUM WEAR VAL-

UE)

43.007 mm (1.6932 in)

Main bushing seat diameter on clutch side (WEAR LIMIT VAL-

UE)

47.142 mm (1.8560 in)

Total thickness for main bushing on clutch side (MINIMUM

WEAR VALUE)

2.04 mm (0.0803 in)

Crankshaft thrust height (MAXIMUM WEAR VALUE)

24.81 mm (0.9768 in)

Crankcase thrust height (MINIMUM WEAR VALUE)

2.3 mm (0.0905 in)

Thickness of the thrust half-bearings on main bushing on clutch

side (MINIMUM WEAR VALUE)

2.31 mm (0.0909 in)

Diameter of crank pin (MINIMUM WEAR VALUE)

39.995 mm (1.5746 in)

The maximum parallelism deviation of the two crankshaft axes (connecting rod pin and main journals

on flywheel side and timing system side) should not exceed 0.02 mm (0.0009 in) at 40 mm (1.5748 in)

distance.

Engine

Engine V85 E4

ENG - 94

Содержание V85 E4













































































































Результаты поиска

Содержание V85 E4

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI V85 E4, Руководство по обслуживанию станции

Результаты поиска

Содержание V85 E4

Отзывы:

Бренды по названию

Популярные бренды