MOTO GUZZI V85 E4 Скачать руководство пользователя страница 62

Страница: 62 / 108

•

(1-2) according to main journal diameter on alternator side.

•

(3-4) according to main journal diameter on clutch side.

SELECTING CRANKSHAFT - CRANKCASE BUSHING CLASSES

Crankcase class

Class 1 crankshaft

Class 2 crankshaft

Class 3 crankshaft

Class 4 crankshaft

Class 1

green-green

yellow-yellow

Class 2

black-black

green-green

Class 3

green-green

yellow-yellow

Class 4

black-black

green-green

Head and timing

Removing the head cover

NOTE

THE OPERATIONS FOR THE REMOVAL OF THE HEAD COVER ARE THE SAME FOR BOTH
SIDES

•

Remove the spark plug cover

•

Disconnect the spark plug tube

•

Remove the blow-by pipe

•

Undo the three fixing screws of the

head cover and remove the gasket

•

Remove the head cover together with

the gaskets

•

Remove the gasket from the head cov-

Engine

Engine V85 E4

ENG - 62

Содержание V85 E4













































































































Результаты поиска

Содержание V85 E4

Отзывы:

Бренды по названию

Популярные бренды

MOTO GUZZI V85 E4, Руководство по обслуживанию станции

Результаты поиска

Содержание V85 E4

Отзывы:

Бренды по названию

Популярные бренды