background image

21

   

User

Manual

11.    

Motion Composites limited 

warranty

    

Refer to the Motion Composites warranty document.

IMPORTANT NOTICE REGARDING CONSUMERS 
RIGHTS

The benefits we give in this manufacturer’s warranty are 
additional to, and do not detract from, any rights and remedies 
that you may have under local consumer protection laws.
This manufacturer’s warranty is governed by the laws of the 
country, province, state or territory in which you purchased 
your Motion Composites product.
In many countries, consumers have statutory rights under local 
consumer laws. Those consumer rights may differ between 
countries, territories, states or provinces, and often cannot be 
excluded.
This Manufacturer’s warranty is not intended to:
•   change or exclude any statutory consumer rights that cannot 

be lawfully changed or excluded; or

•   limit or exclude any right you have against the person who 

sold the Motion composites product to you if that person has 
breached their sales contract with you.

Our

 

responsibility

Motion Composites’ sole obligation and your exclusive remedy 
under this warranty shall be limited to such repair and/or 
replacement. 

Warranty Service

If your wheelchair requires warranty service, please contact 
an authorized Motion Composites Dealer in Canada or an 
authorized international distributor.  In the event of a defect in 
material or workmanship, the Dealer or Distributor must obtain 
a return authorization (RA) number from Motion Composites.  
Motion Composites issues RA numbers only to authorized 
Motion Composites Dealers and Distributors. In the event that 
you do not receive satisfactory warranty service, please write 
directly to 

Motion Composites Customer Service

 at:

160, Armand-Majeau Sud, Saint-Roch-de-l’Achigan, Qc, J0K 
3H0 
or send an email at: [email protected]

Do not return products to our factory without our prior 
consent. 

CONSUMER NOTICE

1

     The foregoing warranty is exclusive, and in lieu of all other 

express warranties, whether written or oral, express or 
implied. Motion Composites shall not be liable for any 
consequential or incidental damages whatsoever. By 
registering your Motion Composites wheelchair, you will be 
deemed to agree with all provisions of this warranty.

2

       It is forbidden to alter or extend the foregoing express 

warranty or to waive any of the limitations or exclusions. 

12. 

Particular damages

12.1    

Damages requiring service by a qualified 

service agent

If any of the following conditions are observed, the wheelchair 
must be serviced by a qualified service agent:

•    Any  wheel  adjustment;
•   Any defective ball bearings of the forks;
•   Any defective ball bearings of the front wheels;

12.2    

Special damages that require the return of 

the wheelchair to the manufacturer

If any of the following conditions are observed, always contact 
your service agent prior to sending your wheelchair for repairs 
at Motion Composites. 

•   Part of the frame  is cracked or broken.
•   The thread of an adjustment nut is damaged.
•   Problems continue to be identified after several adjustments 

or repairs have been made by a qualified service agent.

12.3 

Repair procedure

 

Parts that could be repaired by the owner: 
Rear tire and inner tube. 

•     Parts serviced by the manufacturer or service center: 
     All parts of the wheelchair except for the tires and the inner-

tubes

•     Parts that can be removed and sent to the manufacturer/

distributor or other party for repair:

     Wheels, arm rest, foot rest, upholstery, cushion 

•     Circumstances in which the wheelchair should be sent for 

service:

     Broken bearings, loose spokes, wheel not aligned, loose bolt, 

abnormal vibrations, noise or any deviation in the frame, 
front stem is not perpendicular to floor, broken part like anti-
tippers, back canes, rips or tear on the upholstery and for 
the yearly inspection 

•     Please contact our customer service agent for the complete 

list of distributors or service centers.

 http://www.motioncomposites.com/en/team/

•     Some dealers may offer replacement units during the 

service period. Please contact you service agent for full 
details. Motion Composites will hold replacement parts for a 
minimum of 10 years or propose a compatible spare option.

•     If the wheelchair needs to be sent to a service center or to 

the manufacturer for service, it should be packed carefully 
in a cardboard box fitting the size of the wheelchair. The 
anti-tippers, the foot rest and cushion should be removed 
and packed in a small box inside the larger cardboard 
box containing the wheelchair. The wheelchair should be 
protected with a protective film to prevent from scratches 
or wear.

Содержание APEX Aluminum

































Отзывы: