background image

Operation

C2 Contour Air Drill 

August 2014 

5-15

TAKE SAFETY SERIOUSLY.

Do Not Take Needless Chances!

Caution

Care should be taken when 
working  near  the  air  cart 
while  the  fan  is  running.   
Product  blowing  out  of 
the  system  could  cause 
personal injury.

General Guidelines

The results obtained from the  Morris Contour Drill are 
directly related to the depth uniformity of the unit.  Worn 
points, uneven tire pressures, and bent shanks must be 
avoided to obtain optimum field results.
•  Operating depth should be uniform at all opener 

locations, when spot checking the implement in the 
field.  

•  Check openers running in tractor or air cart tracks 

and adjust depth accordingly.

•  Repair or replace bent shanks.  Bent shanks cause 

openers to work at uneven depths and can cause 
unnecessary ridging.  See Maintenance Section.

•  Keep  tire  pressure  at  the  listed  specifications  to 

maintain proper level.  See Maintenance Section.

•  Have Air Drill moving forward before lowering into 

ground to avoid plugging openers.

•  Avoid sharp turns.  Turns sharp enough to cause 

the inside openers of the air drill to reverse direction 
are not recommended.  This may cause the seed 
openers  to plug.

Содержание C2 Contour





























































































Отзывы: