mori seiki ZL-153 Скачать руководство пользователя страница 515

Страница: 515 / 561

PREPARATION BEFORE STARTING MASS PRODUCTION F-31

LOAD MONITORING FUNCTION B

The operating and setting methods for the load monitoring function B are explained here.

9-1

General

The load monitoring function B is used to detect abnormality of a tool by monitoring the variation in

motor load during cutting.

The function includes the following features:

Teaching operation

The teaching operation is used to detect the reference load (maximum value) of the spindle

and feed axis during the actual cutting process.

Manual setting and display of load monitoring table

The data necessary for load monitoring can be set and displayed on the LOAD MONITOR

SETTING screen.

Load meter display

The load of the spindle or feed axis is displayed on the LOAD MONITOR screen.

Display mode: Bar graph and numeric value

Load monitoring

The load torque of the spindle or axis drive motor is detected to sense warning and alarm

state.

Warning: Start interlock processing (macro input signal processing is optionally provided).

Alarm:

Feed hold and spindle stop processing

<Cautions on using the function>

The function is not adequate for machining causing only slight load variation. This

includes machining to be performed using the tools like finishing tools, small diameter

drills and end mills with which load variation is small. Select the axis to be monitored

according to the type of tools and cutting conditions.

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды